BRLTTY Reference Manual Access to the Console Screen for Blind Persons using Refreshable Braille Displays Nikhil Nair Nicolas Pitre Stéphane Doyon Dave Mielke Version 6.0, February 2019 Copyright © 1995-2019 by The BRLTTY Developers. BRLTTY is free soft- ware, and comes with ABSOLUTELY NO WARRANTY. It is placed under the terms of version 2 or later of The GNU General Public License as pub- lished by The Free Software Foundation. ______________________________________________________________________ Table of Contents 1. Formalities 1.1 License 1.2 Disclaimer 1.3 Contact Information 2. Introduction 2.1 Feature Summary 2.2 System Requirements 3. The Build Procedure 3.1 Installed File Hierarchy 3.2 Installing from a TAR Ball 3.2.1 Build Options 3.2.1.1 System Defaults 3.2.1.2 Directory Specification 3.2.1.3 Build Features 3.2.1.4 Miscellaneous Options 3.2.2 Make File Targets 3.3 Testing BRLTTY 3.4 Starting BRLTTY 3.5 Security Considerations 3.6 Build and Run-Time Restrictions 3.7 Installing from an RPM File 3.8 Other Utilities 3.8.1 brltty-config 3.8.2 brltty-install 3.8.3 brltest 3.8.4 spktest 3.8.5 scrtest 3.8.6 ttbtest 3.8.7 ctbtest 3.8.8 tunetest 4. Using BRLTTY 4.1 Commands 4.1.1 Vertical Motion 4.1.2 Horizontal Motion 4.1.3 Implicit Motion 4.1.4 Feature Activation 4.1.5 Mode Selection 4.1.6 Preference Maintenance 4.1.7 Menu Navigation 4.1.8 Speech Controls 4.1.9 Speech Navigation 4.1.10 Virtual Terminal Switching 4.1.11 Other Commands 4.1.12 Character Commands 4.1.13 Base Commands 4.2 The Configuration File 4.3 Command Line Options 5. Feature Descriptions 5.1 Cursor Routing 5.2 Cut and Paste 5.3 Pointer (Mouse) Support via GPM 5.4 Alert Tunes 5.5 Preferences Settings 5.5.1 The Preferences Menu 5.5.1.1 Navigating the Menu 5.5.1.2 The Menu Items 5.6 The Status Display 5.6.1 Displays with 21 Cells or More 5.6.2 Displays with 20 Cells or Less 5.7 Command Learn Mode 6. Tables 6.1 Text Tables 6.1.1 Text Table Format 6.1.2 Text Table Directives 6.2 Attributes Tables 6.2.1 Attributes Table Format 6.2.2 Attributes Table Directives 6.3 Contraction Tables 6.3.1 Contraction Table Format 6.3.2 Contraction Table Operands 6.3.3 Opcodes 6.3.3.1 Table Administration 6.3.3.2 Special Symbol Definition 6.3.3.3 Character Translation 6.3.3.4 Character Classes 6.4 Key Tables 6.4.1 Key Table Directives 6.4.1.1 The Assign Directive 6.4.1.2 The Bind Directive 6.4.1.3 The Context Directive 6.4.1.4 The Hide Directive 6.4.1.5 The Hotkey Directive 6.4.1.6 The IfKey Directive 6.4.1.7 The Include Directive 6.4.1.8 The Ignore Directive 6.4.1.9 The Map Directive 6.4.1.10 The Note Directive 6.4.1.11 The Superimpose Directive 6.4.1.12 The Title Directive 6.4.2 Keyboard Properties 7. Advanced Topics 7.1 Installing Multiple Versions 7.2 Installation/Rescue Root Disks for Linux 7.3 Future Enhancements 7.4 Known Bugs A. Supported Braille Displays B. Supported Speech Synthesizers C. Driver Identification Codes D. Supported Screen Drivers E. Operand Syntax E.1 Driver Specification E.2 Braille Device Specification E.3 PCM Device Specification E.4 MIDI Device Specification F. Standard Braille Dot Numbering Convention G. North American Braille Computer Code H. MIDI Instrument Table ______________________________________________________________________ 1. Formalities 1.1. License This program is free software. You may redistribute it and/or modify it under the terms of The GNU Lesser General Public License as published by The Free Software Foundation. Version 2.1 (or any later version) of the license may be used. You should have received a copy of the license along with this program. It should be in the file LICENSE-LGPL in the top-level directory. If not, write to the Free Software Foundation Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 1.2. Disclaimer This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY - not even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. 1.3. Contact Information BRLTTY represents the work of a team. For up-to-date information, see BRLTTY's web page at [http://brltty.app/]. As of this writing, the team includes: · Dave Mielke (maintainer, active) Web http://mielke.cc/ E-Mail · Samuel Thibault (active) Web http://dept-info.labri.fr/~thibault/ E-Mail · Mario Lang (active) Web http://delysid.org/ E-Mail · Nicolas Pitre Web http://www.fluxnic.net/ E-Mail · Stéphane Doyon Web http://pages.infinit.net/sdoyon/ E-Mail · Nikhil Nair (author) E-Mail Questions, comments, suggestions, criticisms, and contributions are all welcome. Even though our e-mail addresses are listed above, the best way to contact us is via BRLTTY's mailing list. You can post to the list by sending e-mail to . If you aren't subscribed to the list then your posts will be held for moderator approval. To subscribe, unsubscribe, change settings, view archives, etc, go to the list's information page at http://mielke.cc/mailman/listinfo/brltty. 2. Introduction BRLTTY gives a braille user access to the text consoles of a Linux/Unix system. It runs as a background process (daemon) which operates a refreshable braille display, and can be started very early in the system boot sequence. It enables a braille user, therefore, to easily independently handle aspects of system administration such as single user mode entry, file system recovery, and boot problem analysis. It even greatly eases such routine tasks as logging in. BRLTTY reproduces a rectangular portion of the screen (referred to within this document as `the window') as braille text on the display. Controls on the display can be used to move the window around on the screen, to enable and disable various viewing options, and to perform special functions. 2.1. Feature Summary BRLTTY provides the following capabilities: · Full implementation of the usual screen review facilities. · Choice between block, underline, or no cursor. · Optional underline to indicate specially highlighted text. · Optional use of blinking (rates individually settable) for cursor, special highlighting underline, and/or capital letters. · Screen freezing for leisurely review. · Intelligent cursor routing, allowing easy fetching of cursor within text editors, web browsers, etc., without moving ones hands from the braille display. · A cut-and-paste function (linear or rectangular) which is particularly useful for copying long file names, copying text between virtual terminals, entering complicated commands, etc. · Table driven in-line contracted braille (English and French provided). · Support for multiple braille codes. · Ability to identify an unknown character. · Ability to inspect character highlighting. · An on-line help facility for braille display commands. · A preferences menu. · Basic speech support. · Modular design allowing relatively easy addition of drivers for other braille displays and speech synthesizers. · An Application Programming Interface. 2.2. System Requirements To date, BRLTTY runs under Linux, Solaris, OpenBSD, FreeBSD, NetBSD, and Windows. While ports to other Unix-like operating systems aren't currently planned, we do welcome any interest in such projects. Linux This software has been tested on a variety of Linux systems: · Desktops, laptops, and some PDAs. · Processors from a 386SX20 to a Pentium. · A huge range of memory sizes. · Several distributions including Debian, Red Hat, Slackware, and SuSE. · Many kernels, including 1.2.13, 2.0, 2.2, and 2.4. Solaris This software has been tested on the following Solaris systems: · The Sparc architecture (releases 7, 8, and 9). · The Intel architecture (release 9). OpenBSD This software has been tested on the following OpenBSD systems: · The Intel architecture (release 3.4). FreeBSD This software has been tested on the following FreeBSD systems: · The Intel architecture (release 5.1). NetBSD This software has been tested on the following NetBSD systems: · The Intel architecture (release 1.6). Windows This software has been tested on Windows 95, 98, and XP. On Linux, BRLTTY can inspect the content of the screen completely independently of any logged in user. It does this by using a special device which provides easy access to the contents of the current virtual console. This device was introduced in version 1.1.92 of the Linux kernel, and is normally called either /dev/vcsa or /dev/vcsa0 (on systems with devfs it's called /dev/vcc/a). For this reason, Linux kernel 1.1.92 or later is required if BRLTTY is to be used in this way. This capability: · Allows BRLTTY to be started very early in the system boot sequence. · Enables the braille display to be fully operational during the login prompt. · Makes it much easier for a braille user to perform boot-time system administration tasks. A patch for the screen program is provided (see the Patches subdirectory). It allows BRLTTY to access screen's screen image via shared memory, and, therefore, allows BRLTTY to be used quite effectively on platforms which don't have their own screen content inspection facility. The main weakness of the screen approach is that BRLTTY can't be started until the user has logged in. BRLTTY only works with text-based consoles and applications. It can be used with curses-based applications, but not with any application which either uses special VGA features or requires a graphics console (like the X Window system). You must also, of course, possess a supported refreshable braille display (see section ``Supported Braille Displays'' for the complete list). We hope that additional displays will be supported in the future, so, if you have any vaguely technical programming information for a device which you'd like to see supported, then please let us know (see section ``Contact Information''). Finally, you need tools to build the executable from its source: make, C and C++ compilers, yacc, awk, etc. The development tools provided with standard Unix distributions should suffice. If you have problems, then contact us and we'll compile a binary for you. 3. The Build Procedure BRLTTY can be downloaded from its web site (see section ``Contact Information'' for its location). All releases are provided as compressed ``tar balls''. Newer releases are also provided as ``RPM'' (RedHat Package Manager) files. That tidbit of information has probably peaked your curiosity, and now you just can't wait to get started. It's a good idea, though, to first become familiar with the files which will ultimately be installed. 3.1. Installed File Hierarchy The build procedure should result in the installation of the following files: /bin/ brltty The BRLTTY program. ``brltty-install'' A utility for copying BRLTTY's ``installed file hierarchy'' from one location to another. ``brltty-config'' A utility which sets a number of environment variables to values which reflect the current installation of BRLTTY. /lib/ libbrlapi.a Static archive of the Application Programming Interface. libbrlapi.so Dynamically loadable object for the Application Programming Interface. /lib/brltty/ Your installation of BRLTTY may not have all of the following types of files. They're only created as needed based on the build options you select (see ``Build Options''). brltty-brl.lst A list of the braille display drivers which have been built as dynamically loadable shared objects, and, therefore, which can be selected at run-time. Each line consists of the two- letter identification code for a driver, a tab character, and a description of the braille display which that driver is for. libbrlttybdriver.so.1 The dynamically loadable driver for a braille display, where driver is the two-letter ``driver identification code''. brltty-spk.lst A list of the speech synthesizer drivers which have been built as dynamically loadable shared objects, and, therefore, which can be selected at run-time. Each line consists of the two-letter identification code for a driver, a tab character, and a description of the speech synthesizer which that driver is for. libbrlttysdriver.so.1 The dynamically loadable driver for a speech synthesizer, where driver is the two-letter ``driver identification code''. /lib/brltty/rw/ Files created at run-time, e.g. needed but missing system resources. /etc/ brltty.conf System defaults for BRLTTY. brlapi.key The access key for BrlAPI. /etc/brltty/ Your installation of BRLTTY may not have all of the following types of files. They're only created as needed based on the build options you select (see ``Build Options''). *.conf Driver-specific configuration data. Their names look more or less like brltty-driver.conf, where driver is the two-letter ``driver identification code''. *.atb Attributes tables (see section ``Attributes Tables'' for details). Their names look like name.atb. *.ati Include files for attributes tables. *.ctb Contraction tables (see section ``Contraction Tables'' for details). Their names look like language-country-level.ctb. *.cti Include files for contraction tables. *.ktb Key tables (see section ``Key Tables'' for details). Their names look like name.ktb. *.kti Include files for key tables. *.ttb Text tables (see section ``Text Tables'' for details). Their names look like language.ttb. *.tti Include files for text tables. *.hlp Driver-specific help pages. Their names look more or less like brltty-driver.hlp, where driver is the two-letter ``driver identification code''. /var/lib/BrlAPI/ Local sockets for connecting to the Application Programming Interface. /include/ C header files for the Application Programming Interface. Their names look like brlapi-function.h. The main header is brlapi.h. /include/brltty/ C header files for accessing braille hardware. Their names look like brldefs-driver.h (where driver is the two-letter ``driver identification code''). The headers brldefs.h and api.h are provided for backward compatibility and shouldn't be used. /man/ Man pages. man1/name.1 Man pages for BRLTTY-related user commands. man3/name.3 Man pages for Application Programming Interface library routines. Some optional files which you should be aware of, although they aren't part of the installed file hierarchy, are: /etc/brltty.conf The system defaults configuration file. It's created by the system administrator. See ``The Configuration File'' for details. /etc/brltty-driver.prefs The saved preferences settings file (driver is a two-letter ``driver identification code''). It's created by the ``PREFSAVE'' command. See ``Preferences Settings'' for details. 3.2. Installing from a TAR Ball Here's what to do if you just want to install BRLTTY as quickly as possible, trusting that all of our defaults are correct. 1. Download the source. It'll be a file named brltty-release.tar.gz, e.g. brltty-3.0.tar.gz. 2. Unpack the source into its native hierarchical structure. tar xzf brltty-release.tar.gz This should create the directory brltty-release. 3. Change to the source directory, configure, compile, and install BRLTTY. cd brltty-release ./configure make install This should be done as root. To uninstall BRLTTY, do: cd brltty-release make uninstall That's all there's to it. Now, for those who really want to know what's going on, here are the details. 3.2.1. Build Options The first step in building BRLTTY is to configure it for your system and/or for your personal needs. This is done by running the configure script in BRLTTY's top-level directory. We've tried to make the defaults fit the most common case, so, assuming that you're not attempting to do anything out of the ordinary, you may not need to do anything more complicated than invoke this script without specifying any options at all. ./configure If, however, you have some special requirements, or even if you're just adventurous, you should find out what your choices are. ./configure --help You should also check out the README file in the subdirectory contain- ing the driver for your braille display for any additional display- specific instructions. 3.2.1.1. System Defaults --with-braille-driver=driver Specify the braille display drivers which are to be linked into the BRLTTY binary. Those drivers which aren't listed via this option are built as dynamically loadable shared objects and can still be selected at run-time. Each driver must be identified either by its two-letter ``driver identification code'' or by its proper name (full or abbreviated). The driver identifiers must be separated from one another by a single comma. If a driver identifier is prefixed by a minus sign (-), then that driver is excluded from the build. Any of the following words can also be used as the operand of this option: all Link all of the drivers into the binary. Don't build any of them as dynamically loadable shared objects. This word may also be specified as the final element of a driver list. This is how to specify the default driver when all the drivers are to be linked in. -all Only build those drivers which have been explicitly included via this option. no Don't build any drivers at all. This is equivalent to specifying --without-braille-driver. yes Build all of the drivers as dynamically loadable shared objects. Don't link any of them into the binary. This is equivalent to specifying --with-braille-driver. See the ``braille-driver'' configuration file directive and the ``-b'' command line option for run-time selection. --with-braille-parameters=[driver:]name=value,... Specify the default parameter settings for the braille display drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``braille-parameters'' configuration file directive and the ``-B'' command line option for run-time selection. --with-braille-device=device,... Specify the default device to which the braille display is connected (see section ``Braille Device Specification''). If this option isn't specified then usb: is assumed if USB support is available, bluetooth: is assumed if Bluetooth support is available, and usb:,bluetooth: is assumed if both are available. If neither USB nor Bluetooth support is available then an operating system appropriate path for the primary (first) serial port (device) is assumed. See the ``braille-device'' configuration file directive and the ``-d'' command line option for run-time selection. --with-libbraille=directory Specify the installed location of the Libbraille package, and build the Libbraille braille display driver (see ``Build Restrictions''). Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-libbraille. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/Libbraille, /usr/local/libbraille, /opt/Libbraille, or /opt/libbraille. This is equivalent to specifying --with-libbraille. --with-text-table=file Specify the built-in (fallback) text table (see section ``Text Tables'' for details). The specified table is linked into the BRLTTY binary, and is used either if locale-based autoselection fails or if the requested table can't be loaded. The absolute path to a table outside the source tree may be specified. The .ttb extension is optional. If this option isn't specified, then en-nabcc, a commonly (in North America) used 8-dot variant of the ``North American Braille Computer Code'', is assumed. See the ``text-table'' configuration file directive and the ``-t'' command line option for run-time selection. This setting can be changed with the ``Text Table'' preference. --with-attributes-table=file Specify the built-in (fallback) attributes table (see section ``Attributes Translation'' for details). The specified table is linked into the BRLTTY binary, and is used if the requested table can't be loaded. The absolute path to a table outside the source tree may be specified. The .atb extension is optional. If this option isn't specified, then left_right is assumed. Change it to invleft_right if you'd like it done the old way. See the ``attributes-table'' configuration file directive and the ``-a'' command line option for run-time selection. This setting can be changed with the ``Attributes Table'' preference. --with-speech-driver=driver Specify the speech synthesizer drivers which are to be linked into the BRLTTY binary. Those drivers which aren't listed via this option are built as dynamically loadable shared objects and can still be selected at run-time. Each driver must be identified either by its two-letter ``driver identification code'' or by its proper name (full or abbreviated). The driver identifiers must be separated from one another by a single comma. If a driver identifier is prefixed by a minus sign (-), then that driver is excluded from the build. Any of the following words can also be used as the operand of this option: all Link all of the drivers into the binary. Don't build any of them as dynamically loadable shared objects. This word may also be specified as the final element of a driver list. This is how to specify the default driver when all the drivers are to be linked in. -all Only build those drivers which have been explicitly included via this option. no Don't build any drivers at all. This is equivalent to specifying --without-speech-driver. yes Build all of the drivers as dynamically loadable shared objects. Don't link any of them into the binary. This is equivalent to specifying --with-speech-driver. See the ``speech-driver'' configuration file directive and the ``-s'' command line option for run-time selection. --with-speech-parameters=[driver:]name=value,... Specify the default parameter settings for the speech synthesizer drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``speech- parameters'' configuration file directive and the ``-S'' command line option for run-time selection. --with-flite=directory Specify the installed location of the FestivalLite text-to- speech package, and build the FestivalLite speech synthesizer driver (see ``Build Restrictions''). Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-flite. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/FestivalLite, /usr/local/flite, /opt/FestivalLite, or /opt/flite. This is equivalent to specifying --with-flite. --with-flite-language=language Specify the language which the FestivalLite text to speech engine is to use. The default language is usenglish. --with-flite-lexicon=lexicon Specify the lexicon which the FestivalLite text to speech engine is to use. The default lexicon is cmulex. --with-flite-voice=voice Specify the voice which the FestivalLite text to speech engine is to use. The default voice is cmu_us_kal16. --with-mikropuhe=directory Specify the installed location of the Mikropuhe text-to-speech package, and build the Mikropuhe speech synthesizer driver (see ``Build Restrictions''). Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-mikropuhe. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/Mikropuhe, /usr/local/mikropuhe, /opt/Mikropuhe, or /opt/mikropuhe. This is equivalent to specifying --with-mikropuhe. --with-speechd=directory Specify the installed location of the speech-dispatcher text-to- speech package, and build the speech-dispatcher speech synthesizer driver. Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-speechd. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/speech-dispatcher, /usr/local/speechd, /opt/speech-dispatcher, or /opt/speechd. This is equivalent to specifying --with-speechd. --with-swift=directory Specify the installed location of the Swift text-to-speech package, and build the Swift speech synthesizer driver. Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-swift. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/Swift, /usr/local/swift, /opt/Swift, or /opt/swift. This is equivalent to specifying --with- swift. --with-theta=directory Specify the installed location of the Theta text-to-speech package, and build the Theta speech synthesizer driver (see ``Build Restrictions''). Any of the following words can also be used as the operand of this option: no Don't build the driver. This is equivalent to specifying --without-theta. yes Build the driver if the package can be found in /usr, /usr/local, /usr/local/Theta, /usr/local/theta, /opt/Theta, or /opt/theta. This is equivalent to specifying --with- theta. --with-screen-driver=driver Specify the screen drivers which are to be linked into the BRLTTY binary. Those drivers which aren't listed via this option are built as dynamically loadable shared objects and can still be selected at run-time. Each driver must be identified either by its two-letter driver identification code (see section ``Supported Screen Drivers'') or by its proper name (full or abbreviated). The driver identifiers must be separated from one another by a single comma. If a driver identifier is prefixed by a minus sign (-), then that driver is excluded from the build. Any of the following words can also be used as the operand of this option: all Link all of the drivers into the binary. Don't build any of them as dynamically loadable shared objects. This word may also be specified as the final element of a driver list. This is how to specify the default driver when all the drivers are to be linked in. -all Only build those drivers which have been explicitly included via this option. no Don't build any drivers at all. This is equivalent to specifying --without-screen-driver. yes Build all of the drivers as dynamically loadable shared objects. Don't link any of them into the binary. This is equivalent to specifying --with-screen-driver. The first non-excluded driver becomes the default driver. If this option isn't specified, or if no driver is specifically included, then an operating system appropriate default is selected. If a native driver for the current operating system is available, then that driver is selected; if not, then sc is selected. See the ``screen-driver'' configuration file direc- tive and the ``-x'' command line option for run-time selection. --with-screen-parameters=[driver:]name=value,... Specify the default parameter settings for the screen drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Supported Screen Drivers'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``screen-parameters'' configuration file directive and the ``-X'' command line option for run-time selection. --with-usb-package=package,... Specify the package which is to be used for USB I/O. The package names must be separated from one another by a single comma, and are processed from left to right. The first one which is installed on the system is selected. The following packages are supported: 1. libusb 2. libusb-1.0 Any of the following words can also be used as the operand of this option: no Don't support USB I/O. This is equivalent to specifying --without-usb-package. yes Use native support for USB I/O. If native support isn't available for the current platform then use the first available supported package (as per the order specified above). This is equivalent to specifying --with-usb-package. --with-bluetooth-package=package,... Specify the package which is to be used for Bluetooth I/O. The package names must be separated from one another by a single comma, and are processed from left to right. The first one which is installed on the system is selected. The following packages are supported: 1. (no packages are currently supported) Any of the following words can also be used as the operand of this option: no Don't support Bluetooth I/O. This is equivalent to specifying --without-bluetooth-package. yes Use native support for Bluetooth I/O. If native support isn't available for the current platform then use the first available supported package (as per the order specified above). This is equivalent to specifying --with-bluetooth- package. 3.2.1.2. Directory Specification --with-execute-root=directory Specify the directory at which the ``installed file hierarchy'' is to be rooted at run-time. The absolute path should be supplied. If this option isn't specified, then the system's root directory is assumed. Use this option if you need to install BRLTTY's run-time files in a non-standard location. You need to use this feature, for example, if you'd like to have more than one version of BRLTTY installed at the same time (see section ``Installing Multiple Versions'' for an example of how to do this). --with-install-root=directory Specify the directory beneath which the ``installed file hierarchy'' is to be installed. The absolute path should be supplied. If this option isn't specified, then the run-time package root (see the ``--with-execute-root'' build option) is assumed. This directory is only used by ``make install'' and ``make uninstall''. Use this option if you need to install BRLTTY in a different location than the one from which it'll ultimately be executed. You need to use this feature, for example, if you're building BRLTTY on one system for use on another. --prefix=directory Specify the directory within the ``installed file hierarchy'' where the default directories for the architecture-independent files are to be rooted. These directories include: · the ``writable directory'' · the ``data directory'' · the ``configuration directory'' · the ``manpage directory'' · the ``include directory'' The absolute path should be supplied. If this option isn't specified, then the system's root directory is assumed. This directory is rooted at the directory specified by the ``--with- execute-root'' build option. --exec-prefix=directory Specify the directory within the ``installed file hierarchy'' where the default directories for the architecture-dependent files are to be rooted. These directories include: · the ``program directory'' · the ``library directory'' · the ``API directory'' The absolute path should be supplied. If this option isn't specified, then the directory specified via the ``--prefix'' build option is assumed. This directory is rooted at the direc- tory specified by the ``--with-execute-root'' build option. --libdir=directory Specify the directory within the ``installed file hierarchy'' where the static archive and the dynamically loadable object for the Application Programming Interface are to be installed. The absolute path should be supplied. If this option isn't specified, then the directory specified via the standard configure option --libdir (which defaults to /lib rooted at the directory specified by the ``--exec-prefix'' build option) is assumed. The directory is created if it doesn't exist. --sysconfdir=directory Specify the directory within the ``installed file hierarchy'' where the configuration files are to be installed. The absolute path should be supplied. If this option isn't specified, then the directory specified via the standard configure option --sysconfdir (which defaults to /etc rooted at the directory specified by the ``--prefix'' build option) is assumed. The directory is created if it doesn't exist. --with-program-directory=directory Specify the directory within the ``installed file hierarchy'' where the runnable programs (binaries, executables) are to be installed. The absolute path should be supplied. If this option isn't specified, then the directory specified via the standard configure option --bindir (which defaults to /bin rooted at the directory specified by the ``--exec-prefix'' build option) is assumed. The directory is created if it doesn't exist. --with-library-directory=directory Specify the directory within the ``installed file hierarchy'' where the drivers and other architecture-dependent files are to be installed. The absolute path should be supplied. If this option isn't specified, then the brltty subdirectory of the directory specified via the standard configure option --libdir (which defaults to /lib rooted at the directory specified by the ``--exec-prefix'' build option) is assumed. The directory is created if it doesn't exist. --with-writable-directory=directory Specify the directory within the ``installed file hierarchy'' which may be written to. The absolute path should be supplied. Any of the following words can also be used as the operand of this option: no Don't define a writable directory. This is equivalent to specifying --without-writable-directory. yes Use the default location. This is equivalent to specifying --with-writable-directory. If this option isn't specified, then the rw subdirectory of the directory specified via the ``--with-library-directory'' build option is assumed. The directory is created if it doesn't exist. --with-data-directory=directory Specify the directory within the ``installed file hierarchy'' where the tables, help pages, and other architecture-independent files are to be installed. The absolute path should be supplied. If this option isn't specified, then the brltty subdirectory of the directory specified via the standard configure option --sysconfdir (which defaults to /etc rooted at the directory specified by the ``--prefix'' build option) is assumed. The directory is created if it doesn't exist. --with-manpage-directory=directory Specify the directory within the ``installed file hierarchy'' where the man pages are to be installed. The absolute path should be supplied. If this option isn't specified, then the directory specified via the standard configure option --mandir (which defaults to /man rooted at the directory specified by the ``--prefix'' build option) is assumed. The directory is created if it doesn't exist. --with-include-directory=directory Specify the directory within the ``installed file hierarchy'' where the C header files for the Application Programming Interface are to be installed. The absolute path should be supplied. If this option isn't specified, then the brltty subdirectory of the directory specified via the standard configure option --includedir (which defaults to /include rooted at the directory specified by the ``--prefix'' build option) is assumed. The directory is created if it doesn't exist. 3.2.1.3. Build Features These options are primarily useful when building BRLTTY for use on a boot disk. --enable-standalone-programs Create statically linked, rather than dynamically linked, programs. This option removes all dependencies on shared objects at run-time. Only the default drivers (see the ``--with-braille-driver'', ``--with-speech-driver'', and ``--with-screen-driver'' build options) are compiled. --enable-relocatable-install If this feature is enabled then all internal paths are recalculated to be relative to the program directory. If it's disabled then all internal paths are absolute. This feature allows the entire installed file hierarchy to be copied or moved, in tact, from one place to another, and is primarily intended for use on Windows platforms. --disable-stripping Don't remove the symbol tables from executables and shared objects when installing them. --disable-learn-mode Reduce program size by excluding command learn mode (see section ``Command Learn Mode''). --disable-contracted-braille Reduce program size by excluding support for contracted braille (see section ``Contraction Tables''). --disable-speech-support Reduce program size by excluding support for speech synthesizers. --disable-iconv Reduce program size by excluding support for character set conversion. --disable-icu Reduce program size by excluding support for Unicode-based internationalization. --disable-x Reduce program size by excluding support for X11. --disable-beeper-support Reduce program size by excluding support for the console tone generator. --disable-pcm-support Reduce program size by excluding support for the digital audio interface on the sound card. --enable-pcm-support=interface If a platform provides more than one digital audio interface then the one which is to be used may be specified. Platform Interface Description _______________________________________________________________ Linux oss Open Sound System alsa Advanced Linux Sound Architecture --disable-midi-support Reduce program size by excluding support for the Musical Instrument Digital Interface of the sound card. --enable-midi-support=interface If a platform provides more than one Musical Instrument Digital Interface then the one which is to be used may be specified. Platform Interface Description _______________________________________________________________ Linux oss Open Sound System alsa Advanced Linux Sound Architecture --disable-fm-support Reduce program size by excluding support for the FM synthesizer on an AdLib, OPL3, Sound Blaster, or equivalent sound card. --disable-pm-configfile Reduce program size by excluding support for the Papenmeier driver's configuration file. --disable-gpm Reduce program size by excluding the interface to the gpm application which allows BRLTTY to interact with the pointer (mouse) device (see section ``Pointer (Mouse) Support via GPM''). --disable-api Reduce program size by excluding the Application Programming Interface. --with-api-parameters=name=value,... Specify the default parameter settings for the Application Programming Interface. If the same parameter is specified more than once, then its rightmost assignment is used. For a description of the parameters accepted by the interface, please see the BrlAPI reference manual. See the ``api-parameters'' configuration file directive and the ``-A'' command line option for run-time selection. --disable-caml-bindings Don't build the Caml bindings for the Application Programming Interface. --disable-java-bindings Don't build the Java bindings for the Application Programming Interface. --disable-lisp-bindings Don't build the Lisp bindings for the Application Programming Interface. --disable-python-bindings Don't build the Python bindings for the Application Programming Interface. --disable-tcl-bindings Don't build the Tcl bindings for the Application Programming Interface. --with-tcl-config=path Specify the location of the Tcl configuration script (tclConfig.sh). Either the path to the script itself or to the directory containing it may be supplied. Any of the following words can also be used as the operand of this option: no Use other means to guess if Tcl is available, and, if so, where it has been installed. This is equivalent to specifying --without-tcl-config. yes Search for the script in a few commonly used directories. This is equivalent to specifying --with-tcl-config. 3.2.1.4. Miscellaneous Options --with-init-path=path Specify the path to the real init program for the system. The absolute path should be supplied. If this option is specified, then: 1. The init program should be moved to a new location. 2. brltty should be moved to the init program's original location. 3. When the system runs init at startup, brltty is actually run. It puts itself into the background, and runs the real init in the foreground. This is one (somewhat sneaky) way to have braille right at the outset. It's especially useful for some install/rescue disks. If this option isn't specified, then this feature isn't acti- vated. This option is primarily intended for building a brail- lified installer image. --with-stderr-path=path Specify the path to the file or device where standard erorr output is to be written. The absolute path should be supplied. If this option isn't specified, then this feature isn't activated. This option is primarily intended for building a braillified installer image. 3.2.2. Make File Targets Once BRLTTY has been configured, the next steps are to compile and to install it. These are done by applying the system's make command to BRLTTY's main make file (Makefile in the top-level directory). BRLTTY's make file supports most of the common application maintenance targets. They include: make A shortcut for make all. make all Compile and link the BRLTTY executable, its drivers and their help pages, its test programs, and a few other small utilities. make install Complete the compile and link phase (see ``make all''), and then install the BRLTTY executable, its data files, drivers, and help pages, in the correct places and with the correct permissions. make uninstall Remove the BRLTTY executable, its data files, drivers, and help pages, from the system. make clean Ensure that the next compile and link (see ``make all'') will be done from scratch by removing the results of compiling, linking, and testing from the source directory structure. This includes the removal of object files, executables, dynamically loadable shared objects, driver lists, help pages, temporary header files, and core files. make distclean In addition to removing the results of compiling and linking (see ``make clean''): · Remove the results of BRLTTY configuration (see ``Build Options''). This includes the removal of config.mk, config.h, config.cache, config.status, and config.log. · Remove other files from the source directory structure which tend to accumulate over time but which don't belong there. This includes the removal of editor backup files, test case results, rejected patch hunks, and copies of original source files. 3.3. Testing BRLTTY After compiling, linking, and installing BRLTTY, it's a good idea to give it a quick test before activating it permanently. To do so, invoke it with the command: brltty -bdriver -ddevice For driver, specify the two-letter ``driver identification code'' cor- responding to your braille display. For device, specify the full path for the device to which your braille display is connected. If you don't want to explicitly identify the driver and device each time you start BRLTTY, then you can take two approaches. You can establish system defaults via the ``braille-driver'' and the ``braille-device'' configuration file directives, and/or compile your needs right into BRLTTY via the ``--with-braille-driver'' and the ``--with-braille-device'' build options. If all is well, BRLTTY's version identification message should appear on the braille display for a few seconds (see the ``-M'' command line option). After it goes away (which you can hasten by pressing any key on the display), the area of the screen where the cursor is should appear. This means that you should expect to see your shell's command prompt. Then, as you enter your next command, each character should appear on the display as it's typed on the keyboard. If this is your experience, then leave BRLTTY running, and enjoy it. If this isn't your experience, then it may be necessary to test each driver separately in order to isolate the source of the problem. The screen driver can be tested with ``scrtest'', and the braille display driver can be tested with ``brltest''. If you experience a problem which requires a lot of digging, then you may wish to use the following brltty command line options: · ``-ldebug'' to log lots of diagnostic messages. · ``-n'' to keep BRLTTY in the foreground. · ``-e'' to direct diagnostic messages to standard error rather than to the system log. 3.4. Starting BRLTTY BRLTTY, when properly installed, is invoked with the single command brltty. A configuration file (see section ``The Configuration File'' for details) can be created in order to establish system defaults for such things as the location of the preferences file, the braille display driver to be used, the device to which the braille display is connected, and the text table to be used. Many options (see section ``Command Line Options'' for details) allow explicit run-time specification of such things as the location of the configuration file, any defaults established within the configuration file, and some characteristics which have reasonable defaults but which those who think they know what they're doing may wish to play with. The ``-h'' option displays a summary of all the options. The ``-V'' option displays the current version of the program, the API, and the selected drivers. The ``-v'' option displays the values of the options after all sources have been considered. It's probably best to have the system automatically start BRLTTY as part of the boot sequence so that the braille display is already up and running when the login prompt appears. Most (probably all) distributions provide a script wherein user-supplied applications can be safely started near the end of the boot sequence. The name of this script is distribution-dependent. Here are the ones we know about so far: Red Hat /etc/rc.d/rc.local Starting BRLTTY from this script is a good approach (especially for new users). Just add a set of lines like these: if [ -x /bin/brltty -a -f /etc/brltty.conf ] then /bin/brltty fi This can usually be abbreviated to the somewhat less readable form: [ -x /bin/brltty -a -f /etc/brltty.conf ] && /bin/brltty Don't add these lines before the first line (which usually looks like #!/bin/sh). If the braille display is to be used by a system administrator, then it should probably be started as early as possible during the boot sequence (like before the file systems are checked) so that the display is usable in the event that something goes wrong during these checks and the system drops into single user mode. Again, exactly where it's best to do this is distribution-dependent. Here are the places we know about so far: Debian /etc/init.d/boot (for older releases) /etc/init.d/ (for newer releases) A brltty package is provided (see [http://packages.debian.org/brltty]) as of release 3.0 (Woody). Since this package takes care of starting BRLTTY, there's no need for user-supplied code to do so if it's installed. If you need the daemon to run with some command-line options, you can change the contents between quotes on the directive ARGUMENTS in the /etc/default/brltty file. RedHat /etc/rc.d/rc.sysinit Beware that later releases, in order to support a more user- oriented system initialization procedure, have this script reinvoke itself such that it's under the control of initlog. Look, probably right up near the top, for a set of lines like these: # Rerun ourselves through initlog if [ -z "$IN_INITLOG" ]; then [ -f /sbin/initlog ] && exec /sbin/initlog $INITLOG_ARGS -r /etc/rc.sysinit fi Starting BRLTTY before this reinvocation results in two BRLTTY pro- cesses running at the same time, and that'll give you no end of problems. If your version of this script has this feature, then make sure you start BRLTTY after the lines which implement it. Slackware /etc/rc.d/rc.S SuSE /sbin/init.d/boot An alternative is to start BRLTTY from /etc/inittab. You have two choices if you choose this route. · If you want it to be started really early but don't need it to be automatically restarted if it dies, then add a line like this before the first :sysinit: line which is already in there. brl::sysinit:/bin/brltty · If you don't mind it being started later but do want it to be automatically restarted if it dies, then add a line like this anywhere within the file. brl:12345:respawn:/bin/brltty -n The ``-n'' (--nodaemon) option is very important when running BRLTTY with init's respawn facility. You'll end up with hundreds of BRLTTY processes all running at the same time if you forget to specify it. Check that the identifier (brl in these examples) isn't already being used by another entry, and, if it is, choose a different one which isn't. Note that a command like kill -TERM is sufficient to stop BRLTTY in its tracks. If it dies during entry into single user mode, for example, it may well be due to a problem of this nature. Some systems, as part of the boot sequence, probe the serial ports (usually in order to automatically find the mouse and deduce its type). If your braille display is using a serial port, this kind of probing may be enough to get it confused. If this happens to you, then try restarting the braille driver (see the ``RESTARTBRL'' command). Better yet, turn off the serial port probing. Here's what we know so far about how to do this: Red Hat The probing is done by a service named kudzu. Use the command chkconfig --list kudzu to see if it's been enabled. Use the command chkconfig kudzu off to disable it. Later releases allow you to let kudzu run without probing the serial ports. To do this, edit the file /etc/syscon- fig/kudzu, and set SAFE to yes. If you want to start BRLTTY before any file systems are mounted, then ensure that all of its components are installed within the root file system. See the ``--with-execute-root'', ``--bindir'', ``--libdir'', ``--with-writable-directory'', and ``--with-data-directory'' build options. 3.5. Security Considerations BRLTTY needs to run with root privileges because it needs read and write access for the port to which the braille display is connected, read access to /dev/vcsa or equivalent (to query the screen dimensions and the cursor position, and to review the current screen content and highlighting), and read and write access to the system console (for arrow key entry during cursor routing, for input character insertion during paste, for special key simulation using keys on the braille display, for retrieving output character translation and screen font mapping tables, and for activation of the internal beeper). Access to the needed devices can, of course, be granted to a non-root user by changing the file permissions associated with the devices. Merely having access to the console, however, isn't enough because activating the internal beeper and simulating key strokes still require root privilege. So, if you're willing to give up cursor routing, cut&paste, beeps, and all that, you can run BRLTTY without root priviledge. 3.6. Build and Run-Time Restrictions Alert Tunes Some platforms don't support all of the tune devices. See the ``Tune Device'' preference for details. FestivalLite Speech Synthesizer Driver The driver for the FestivalLite text to speech engine is only built if that package has been installed. This driver and the driver for the Theta text to speech engine (see the ``--with-theta'' build option) cannot be simultaneously linked into the BRLTTY binary (see the ``--with-speech-driver'' build option) because their run-time libraries contain conflicting symbols. Libbraille Braille Display Driver The driver for the Libbraille package is only built if that package has been installed. Mikropuhe Speech Synthesizer Driver The driver for the Mikropuhe text to speech engine is only built if that package has been installed. This driver cannot be included if the BRLTTY binary is statically linked (see the ``--enable-standalone-programs'' build option) because a static archive isn't included with the package. Theta Speech Synthesizer Driver The driver for the Theta text to speech engine is only built if that package has been installed. This driver and the driver for the FestivalLite text to speech engine (see the ``--with-flite'' build option) cannot be simultaneously linked into the BRLTTY binary (see the ``--with- speech-driver'' build option) because their run-time libraries contain conflicting symbols. If this driver is built as a dynamically loadable shared object then $THETA_HOME/lib must be added to the LD_LIBRARY_PATH environment variable before BRLTTY is invoked because the shared objects within the package don't contain run-time search paths for their dependencies. ViaVoice Speech Synthesizer Driver The driver for the ViaVoice text to speech engine is only built if that package has been installed. This driver cannot be included if the BRLTTY binary is statically linked (see the ``--enable-standalone-programs'' build option) because a static archive isn't included with the package. VideoBraille Braille Display Driver The driver for the VideoBraille braille display is built on all systems, but only works on Linux. 3.7. Installing from an RPM File To install BRLTTY from an RPM (RedHat Package Manager) file, do the following: 1. Download the binary package which corresponds to your hardware. It'll be a file named brltty-release-version.architecture.rpm, e.g. brltty-3.0-1.i386.rpm. 2. Install the package. rpm -Uvh brltty-release-version.architecture.rpm This should be done as root. Strictly speaking, the -U (update) option is the only one which is necessary. The -v (verbose) option displays the name of the package as it's being installed. The -h (hashes) option displays a progress meter (using hash signs). For the brave, we also provide the source RPM (.src.rpm) file, but that's beyond the scope of this document. To uninstall BRLTTY, do: rpm -e brltty 3.8. Other Utilities Building BRLTTY also results in the building of a few small helper and diagnostic utilities. 3.8.1. brltty-config This utility sets a number of environment variables to values which reflect the current installation of BRLTTY (see ``Build Options''). It should be executed within an existing shell environment, i.e. not as a command in its own right, and can only be used by scripts which support Bourne Shell syntax. . brltty-config The following environment variables are set: BRLTTY_VERSION The version number of the BRLTTY package. BRLTTY_EXECUTE_ROOT Run-time root for the installed package. Configured via the ``--with-execute-root'' build option. BRLTTY_PROGRAM_DIRECTORY Directory for runnable programs (binaries, executables). Configured via the ``--with-program-directory'' build option. BRLTTY_LIBRARY_DIRECTORY Directory for drivers. Configured via the ``--with-library- directory'' build option. BRLTTY_WRITABLE_DIRECTORY Directory which can be written to. Configured via the ``--with- writable-directory'' build option. BRLTTY_DATA_DIRECTORY Directory for tables and help pages. Configured via the ``--with-data-directory'' build option. BRLTTY_MANPAGE_DIRECTORY Directory for manual pages. Configured via the ``--with- manpage-directory'' build option. BRLTTY_INCLUDE_DIRECTORY Directory for BrlAPI's C header files. Configured via the ``--with-include-directory'' build option. BRLAPI_VERSION The version number of BrlAPI (BRLTTY's Application Programming Interface). BRLAPI_RELEASE The full release number of BrlAPI. BRLAPI_AUTH The name of BrlAPI's key file. In addition, the following standard autoconf environment variables are also set: prefix Subroot for architecture-independent files. Configured via the ``--prefix'' build option. exec_prefix Subroot for architecture-dependent files. Configured via the ``--exec-prefix'' build option. bindir Default location for ``program directory''. Configured via the --bindir build option. libdir Directory for BrlAPI's static archive and dynamically loadable object. Default anchor for ``library directory''. Configured via the ``--libdir'' build option. sysconfdir Directory for configuration files. Default anchor for ``data directory''. Configured via the ``--sysconfdir'' build option. mandir Default location for ``manual pages directory''. Configured via the --mandir build option. includedir Default anchor for ``header files directory''. Configured via the --includedir build option. 3.8.2. brltty-install This utility copies BRLTTY's ``installed file hierarchy'' from one location to another. brltty-install to [from] to The location to which the ``installed file hierarchy'' is to be copied. It must be an existing directory. from The location from which the ``installed file hierarchy'' is to be taken. If it's specified, then it must be an existing directory. If it's not specified, then the location used for the build is assumed. This utility can be used, for example, to copy BRLTTY to a root disk. If a root floppy is mounted as /mnt, and BRLTTY is installed on the main system, then typing brltty-install /mnt copies BRLTTY, along with all of its data and library files, to the root floppy. Some problems have been experienced when copying BRLTTY between systems with different versions of the shared C library. This is worth investigating if you have difficulties. 3.8.3. brltest This utility tests a braille display driver, and also provides an interactive way to learn what the keys on the braille display do. It should be run as root. brltest -option ... [driver [name=value ...]] driver The driver for the braille display. It must be a two-letter ``driver identification code''. If it's not specified, then the first driver configured via the ``--with-braille-driver'' build option is assumed. name=value Set a braille display driver parameter. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. -ddevice --device=device The absolute path for the device to which the braille display is connected. If it's not specified, then the device configured via the ``--with-braille-device'' build option is assumed. -Ddirectory --data-directory=directory The absolute path for the directory wherein the driver data files reside. If it's not specified, then the directory configured via the ``--with-data-directory'' build option is assumed. -Ldirectory --library-directory=directory The absolute path for the directory wherein the drivers reside. If it's not specified, then the directory configured via the ``--libdir'' build option is assumed. -Wdirectory --writable-directory=directory The absolute path for a directory which can be written to. If it's not specified, then the directory configured via the ``--with-writable-directory'' build option is assumed. -h --help Display a summary of the command line options, and then exit. This utility uses BRLTTY's ``Command Learn Mode''. The key press timeout (after which this utility exits) is 10 seconds. The message hold time (used for non-final segments of long messages) is 4 seconds. 3.8.4. spktest This utility tests a speech synthesizer driver. It may need to be run as root. spktest -option ... [driver [name=value ...]] driver The driver for the speech synthesizer. It must be a two-letter ``driver identification code''. If it's not specified, then the first driver configured via the ``--with-speech-driver'' build option is assumed. name=value Set a speech synthesizer driver parameter. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. -tstring --text-string=string The text to be spoken. If it's not specified, then standard input is read. -Ddirectory --data-directory=directory The absolute path for the directory wherein the driver data files reside. If it's not specified, then the directory configured via the ``--with-data-directory'' build option is assumed. -Ldirectory --library-directory=directory The absolute path for the directory wherein the drivers reside. If it's not specified, then the directory configured via the ``--libdir'' build option is assumed. -h --help Display a summary of the command line options, and then exit. 3.8.5. scrtest This utility tests the screen driver. It must be run as root. scrtest -option ... [name=value ...] name=value Set a screen driver parameter. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. -lcolumn --left=column Specify the starting (left) column (zero-origin) of the region. If this value isn't supplied, then a default value, based on the specified width, is selected such that the region is horizontally centred. -ccount --columns=count Specify the width of the region (in columns). If this value isn't supplied, then a default value, based on the specified starting column, is selected such that the region is horizontally centred. -trow --top=row Specify the starting (top) row (zero-origin) of the region. If this value isn't supplied, then a default value, based on the specified height, is selected such that the region is vertically centred. -rcount --rows=count Specify the height of the region (in rows). If this value isn't supplied, then a default value, based on the specified starting row, is selected such that the region is vertically centred. -h --help Display a summary of the command line options, and then exit. Notes: · If neither a starting column nor a region width is specified, then the region is horizontally-centred and starts at column 5. · If neither a starting row nor a region height is specified, then the region is vertically-centred and starts at row 5. The following is written to standard output: 1. A line detailing the dimensions of the screen. Screen: widthxheight 2. A line detailing the position (zero-origin) of the cursor. Cursor: [column,row] 3. A line detailing the size of the selected screen region, and the position (zero-origin) of its top-left corner. Region: widthxheight@[column,row] 4. The contents of the selected screen region. Unprintable characters are written as blanks. 3.8.6. ttbtest This utility tests a text table (see section ``Text Tables''). ttbtest -option ... input-table output-table input-table The file system path to the input text table. If it's relative then it's anchored at the directory configured via the ``--with- data-directory'' build option. output-table The file system path to the output text table. If it's relative then it's anchored at the current working directory. If this parameter isn't supplied then no output table is written. -iformat --input-format=format Specify the format of the input table. If this option isn't supplied then the format of the input table is deduced from the extension of the input table's file name. -oformat --output-format=format Specify the format of the output table. If this option isn't supplied then the format of the output table is deduced from the extension of the output table's file name. -ccharset --charset=charset Specify the name of the 8-bit character set to use when interpreting the tables. If this option isn't supplied then the host's character set is used. -e --edit Invoke the text table editor. If the output table is specified then changes are written to it. If not then the input table is rewritten. -h --help Display a summary of the command line options, and then exit. If no special action is requested then the output table is optional. If it is not specified then the input table is checked. If it is specified then the input table is converted. The following table formats are supported: ttb BRLTTY sbl SuSE Blinux a2b Gnopernicus gnb Gnome Braille 3.8.7. ctbtest This utility tests a contraction table (see section ``Contraction Tables''). The text read from the input files (or standard input) is rewritten to standard output as contracted braille. ctbtest -option ... input-file ... input-file The list of files to be processed. Any number of files may be specified. They're processed from left to right. The special file name - is interpreted to mean standard input. If no files are specified then standard input is processed. -cfile --contraction-table=file The file system path to the contraction table. If it's relative then it's anchored at the directory configured via the ``--with- data-directory'' build option. The .ctb extension is optional. If this option isn't supplied then en-us-g2 is assumed. -tfile|auto --text-table=file|auto Specify the text table (see section ``Text Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with- execute-root'' build options for more details). The .ttb extension is optional. See the ``text-table'' configuration file directive for the default run-time setting. This setting can be changed with the ``Text Table'' preference. -wcolumns --output-width=columns The maximum length of an output line. Each contracted input line is wrapped into as many output lines as necessary. If this option isn't specified then there's no limit, and there's a one- to-one correspondence between input and output lines. -h --help Display a summary of the command line options, and then exit. The text table is used: · To define the output character set so that the contracted braille will be displayed correctly. The same table as will be used by BRLTTY when the output is read should be specified. · To define the braille representations of those characters defined within the contraction table as = (see section ``Character Translation''). The brf.ttb text table is provided for use with this utility. It defines the format used within .brf files. This is also the preferred format used by most braille printers and within electronically distributed braille documents. This table effectively allows this utility to be used as a text to braille translator. 3.8.8. tunetest This utility tests the alert tunes facility, and also provides an easy way to compose new tunes. It may need to be run as root. tunetest -option ... {note duration} ... note A standard MIDI note number. It must be an integer from 1 through 127, with 60 representing Middle C. Each value represents a standard chromatic semi-tone, with the next lower and higher values representing, respectively, the next lower and higher notes. The lowest value (1) represents the fifth C-Sharp below Middle C, and the highest value (127) represents the sixth G above Middle C. duration The duration of the note in milliseconds. It must be an integer from 1 through 255. -ddevice --device=device The device on which to play the tune. beeper The internal beeper (console tone generator). pcm The digital audio interface on the sound card. midi The Musical Instrument Digital Interface on the sound card. fm The FM synthesizer on an AdLib, OPL3, Sound Blaster, or equivalent sound card. The device name may be abbreviated. See the ``Tune Device'' preference for details regarding the default device and platform restrictions. -vloudness --volume=loudness Specify the output volume (loudness) as a percentage of the maximum. The default output volume is 50. -pdevice --pcm-device=device Specify the device to use for digital audio (see section ``PCM Device Specification''). This option isn't available if the ``--disable-pcm-support'' build option was specified. -mdevice --midi-device=device Specify the device to use for the Musical Instrument Digital Interface (see section ``MIDI Device Specification''). This option isn't available if the ``--disable-midi-support'' build option was specified. -iinstrument --instrument=instrument The instrument to use if the selected device is midi. For the complete list of instruments, see the ``MIDI Instrument Table''. The default instrument is an acoustic grand piano. The words comprising the instrument name must be separated from one another by a single minus sign rather than by spaces, and any of the words may be abbreviated. An acoustic grand piano, for example, may be specified as a-gra-pi. -h --help Display a summary of the command line options, and then exit. 4. Using BRLTTY Before starting BRLTTY, you need to set up your braille display. In most cases this is done simply by connecting it to an available serial port, and then turning it on. After your display has been set up, run BRLTTY simply by typing the command brltty at a shell prompt (this must be done as root). Check the ``-d'' command line option, the ``braille-device'' configuration file directive, and the ``--with- braille-device'' build option for alternatives regarding how to tell BRLTTY which device your display is connected to. Check the ``-b'' command line option, the ``braille-driver'' configuration file directive, and the ``--with-braille-driver'' build option for alternatives regarding how to tell BRLTTY which kind of braille display you have. Check the ``-B'' command line option, and the ``braille-parameters'' configuration file directive for alternatives regarding how to pass parameters to the driver for your braille display. A message giving the program name (BRLTTY) and its version number will appear briefly (see the ``-M'' command line option) on the braille display. The display will then show a small area of the screen including the cursor. By default, the cursor is represented as dots 7 and 8 superimposed on the character it is on. Any screen activity will be reflected on the braille display. The display will also follow the progress of the cursor on the screen. This feature is known as cursor tracking. Just typing on the keyboard and reading the display, however, isn't enough. Try entering a command which will cause an error, and pressing enter. The error appears on the screen, but, unless you have a multi-line display, the chances are that it isn't visible on the braille display. All you see thereon is another shell prompt. What's needed, then, is some way to move the braille window around the screen. The keys on the braille display itself can be used to send commands to BRLTTY which, in addition to a lot of other things, can also do exactly that. 4.1. Commands Unfortunately, the various braille displays don't offer a standard set of controls. Some have the six standard dot keys, some have eight, and others have none. Some have thumb keys, but there's no standard number of them. Some have a button above each braille cell. Some have rocker switches. Some have an easy-to-reach bar which works much like a joystick. Most have varying combinations of the above. Because the nature and layout of each display is so different, please refer to the documentation for your particular display in order to find out exactly what its keys do. BRLTTY commands are referred to by name within this manual. If you forget which key(s) on your braille display to use for a particular command, then refer to its driver's help page. The main key you should immediately commit to memory, therefore, is the one for the ``HELP'' command. Use the regular motion keys (as described below) to navigate the help page, and press the help key again to quit. 4.1.1. Vertical Motion See also the ``PRINDENT/NXINDENT'', and the ``PRDIFCHAR/NXDIFCHAR'' routing key commands. LNUP/LNDN Go up/down one line. If identical line skipping has been activated (see the ``SKPIDLNS'' command), then these commands, rather than moving exactly one line, are aliases for the ``PRDIFLN/NXDIFLN'' commands. WINUP/WINDN Go up/down one window. If the window is only 1 line high then move 5 lines. PRDIFLN/NXDIFLN Go up/down to the nearest line with different content. If identical line skipping has been activated (see the ``SKPIDLNS'' command), then these commands, rather than skipping identical lines, are aliases for the ``LNUP/LNDN'' commands. ATTRUP/ATTRDN Go up/down to the nearest line with different attributes (character highlighting). TOP/BOT Go to the top/bottom line. TOP_LEFT/BOT_LEFT Go to the top-left/bottom-left corner. PRPGRPH/NXPGRPH Go to the nearest line of the previous/next paragraph (the first non-blank line beyond the nearest blank line). The current line is included when searching for the inter-paragraph space. PRPROMPT/NXPROMPT Go to the previous/next command prompt. PRSEARCH/NXSEARCH Search backward/forward for the nearest occurrence of the character string within the cut buffer (see ``Cut and Paste'') which isn't within the braille window. The search proceeds to the left/right, starting at the character immediately to the left/right of the window, and wrapping at the edge of the screen. The search isn't case sensitive. 4.1.2. Horizontal Motion See also the ``SETLEFT'' routing key command. CHRLT/CHRRT Go left/right one character. HWINLT/HWINRT Go left/right half a window. FWINLT/FWINRT Go left/right one window. These commands are particularly useful because they automatically wrap when they reach the edge of the screen. Other features, like their ability to skip blank windows (see the ``SKPBLNKWINS'' command), further enhance their usefulness. FWINLTSKIP/FWINRTSKIP Go left/right to the nearest non-blank window. LNBEG/LNEND Go to the beginning/end of the line. 4.1.3. Implicit Motion See also the ``GOTOMARK'' routing key command. HOME Go to where the cursor is. BACK Go back to where the most recent motion command put the braille window. This is an easy way to get right back to where you were reading after an unexpected event (like cursor tracking) moves the braille window at an inopportune moment. RETURN · If the most recent motion of the braille window was automatic, e.g. as a result of cursor tracking, then go back to where the most recent motion command put it (see the ``BACK'' command). · If the cursor isn't within the braille window then go to where the cursor is (see the ``HOME'' command). 4.1.4. Feature Activation Each of these commands has three forms: activate (turn the feature on), deactivate (turn the feature off), and toggle (if it's off then turn it on, and if it's on then turn it off). Unless specifically noted, each of these features is initially off, and, when on, affects BRLTTY's operation as a whole. The initial setting of some of these features can be changed via the ``preferences menu''. FREEZE Freeze the screen image. BRLTTY makes a copy of the screen (content and attributes) as of the moment when the screen image is frozen, and then ignores all updating of the screen until it's unfrozen. This feature makes it easy, for example, to sample the output of an application which writes too much too quickly. DISPMD Show the highlighting (the attributes) of each character within the braille window, rather than the characters themselves (the content). This feature is useful, for example, when you need to locate a highlighted item. When showing screen content, the text table is used (see the ``-t'' command line option, the ``text-table'' configuration file directive, and the ``--with- text-table'' build option). When showing screen attributes, the attributes table is used (see the ``-a'' command line option, the ``attributes-table'' configuration file directive, and the ``--with-attributes-table'' build option). This feature only affects the current virtual terminal. SIXDOTS Show characters using 6-dot, rather than 8-dot, braille. Dots 7 and 8 are still used by other features like cursor representation and highlighted character underlining. If a contraction table has been selected (see the ``-c'' command line option and the ``contraction-table'' configuration file directive), then it is used. This setting can also be changed with the ``Text Style'' preference. SLIDEWIN If cursor tracking (see the ``CSRTRK'' command) is on, then, whenever the cursor moves too close to (or beyond) either end of the braille window, horizontally reposition the window such that the cursor, while remaining on that side, is nearer the centre. If this feature is off, then the braille window is always positioned such that its left end is a multiple of its width from the left edge of the screen. This setting can also be changed with the ``Sliding Window'' preference. SKPIDLNS Rather than explicitly moving exactly one line either up or down, skip past lines which have the same content as the current line. This feature affects the ``LNUP/LNDN'' commands, as well as the line wrapping feature of the ``FWINLT/FWINRT'' and ``FWINLTSKIP/FWINRTSKIP'' commands. This setting can also be changed with the ``Skip Identical Lines'' preference. SKPBLNKWINS Skip past blank windows when reading either forward or backward. This feature affects the ``FWINLT/FWINRT'' commands. This setting can also be changed with the ``Skip Blank Windows'' preference. CSRVIS Show the cursor by superimposing a dot pattern (see the ``CSRSIZE'' command) on top of the character where it is. This feature is initially on. This setting can also be changed with the ``Show Cursor'' preference. CSRHIDE Hide the cursor (see the ``CSRVIS'' command) in order to accurately read the character beneath it. This feature only affects the current virtual terminal. CSRTRK Track (follow) the cursor. If the cursor moves to a location which isn't within the braille window, then automatically move the braille window to the cursor's new location. You'll usually want this feature turned on since it minimizes the effects of screen scrolling, and since, during input, the region wherein you're currently typing is always visible. If this feature causes the braille window to jump at an inopportune moment, then use the ``BACK'' command to get back to where you were reading. You may need to turn this feature off when using an application which continually updates the screen while maintaining a fixed data layout. This feature is initially on. This feature only affects the current virtual terminal. CSRSIZE Represent the cursor with all eight dots (a solid block), rather than with just dots 7 and 8 (an underline). This setting can also be changed with the ``Cursor Style'' preference. CSRBLINK Blink (turn on and off according to a predefined interval) the symbol representing the cursor (see the ``CSRVIS'' command). This setting can also be changed with the ``Blinking Cursor'' preference. ATTRVIS Underline (with combinations of dots 7 and 8) highlighted characters. no underline White on black (normal), gray on black, white on blue, black on cyan. dots 7 and 8 Black on white (reverse video). dot 8 Everything else. This setting can also be changed with the ``Show Attributes'' preference. ATTRBLINK Blink (turn on and off according to a predefined interval) the attribute underline (see the ``ATTRVIS'' command). This feature is initially on. This setting can also be changed with the ``Blinking Attributes'' preference. CAPBLINK Blink (turn on and off according to a predefined interval) capital (uppercase) letters. This setting can also be changed with the ``Blinking Capitals'' preference. TUNES Play a short predefined tune (see ``Alert Tunes'') whenever a significant event occurs. This feature is initially on. This setting can also be changed with the ``Alert Tunes'' preference. AUTOREPEAT Automatically repeat a command at a regular interval after an initial delay while its key (combination) remains pressed. Only some drivers support this functionality, the primary limitation being that many braille displays don't signal key presses and key releases as distinctly separate events. This feature is initially on. This setting can also be changed with the ``Autorepeat'' preference. AUTOSPEAK Automatically speak: · the new line when the braille window is moved vertically. · characters which are entered or deleted. · the character to which the cursor is moved. This feature is initially off. This setting can also be changed with the ``Autospeak'' preference. 4.1.5. Mode Selection HELP Switch to the braille display driver's help page. This is where you can find an on-line summary of things like what your braille display's keys do, and how to interpret its status cells. Use the regular ``vertical'' and ``horizontal'' motion commands to navigate the help page. Invoke the help command again to return to the screen. INFO Switch to the status display (see section ``The Status Display'' for full details). It presents a summary including the position of the cursor, the position of the braille window, and the states of a number of BRLTTY's features. Invoke this command again to return to the screen. LEARN Switch to command learn mode (see section ``Command Learn Mode'' for full details). This is how you can interactively learn what your braille display's keys do. Invoke this command again to return to the screen. This command isn't available if the ``--disable-learn-mode'' build option was specified. 4.1.6. Preference Maintenance PREFMENU Switch to the preferences menu (see ``The Preferences Menu'' for full details). Invoke this command again to return to normal operation. PREFSAVE Save the current preferences settings (see ``Preferences'' for full details). PREFLOAD Restore the most recently saved preferences settings (see ``Preferences'' for full details). 4.1.7. Menu Navigation MENU_FIRST_ITEM/MENU_LAST_ITEM Go to the first/last item in the menu. MENU_PREV_ITEMMENU_NEXT_ITEM/ Go to the previous/next item in the menu. MENU_PREV_SETTING/MENU_NEXT_SETTING Decrement/increment the current menu item's setting. 4.1.8. Speech Controls SAY_LINE Speak the current line. The ``Say-Line Mode'' preference determines if pending speech is discarded first. SAY_ABOVE Speak the top portion of the screen (ending with the current line). SAY_BELOW Speak the bottom portion of the screen (starting with the current line). MUTE Stop speaking immediately. SPKHOME Go to where the speech cursor is. SAY_SLOWER/SAY_FASTER Decrease/increase the speech rate (see also the ``Speech Rate'' preference). This command is only available if a driver which supports it is being used. SAY_SOFTER/SAY_LOUDER Decrease/increase the speech volume (see also the ``Speech Volume'' preference). This command is only available if a driver which supports it is being used. 4.1.9. Speech Navigation SPEAK_CURR_CHAR a 4.1.10. Virtual Terminal Switching See also the ``SWITCHVT'' routing key command. SWITCHVT_PREV/SWITCHVT_NEXT Switch to the previous/next virtual terminal. 4.1.11. Other Commands CSRJMP_VERT Route (bring) the cursor to anywhere on the top line of the braille window (see ``Cursor Routing'' for full details). The cursor is moved by simulating vertical arrow-key presses. This command doesn't always work because some applications either move the cursor somewhat unpredictably or use the arrow keys for purposes other than cursor motion. It's somewhat safer than the other cursor routing commands, though, because it makes no attempt to simulate the left- and right-arrows. PASTE Insert the characters within the cut buffer at the current cursor location (see ``Cut and Paste'' for full details). RESTARTBRL Stop, and then restart the braille display driver. RESTARTSPEECH Stop, and then restart the speech synthesizer driver. 4.1.12. Character Commands ROUTE Route (bring) the cursor to the character associated with the routing key (see ``Cursor Routing'' for full details). The cursor is moved by simulating arrow-key presses. This command doesn't always work because some applications either move the cursor somewhat unpredictably or use the arrow keys for purposes other than cursor motion. CUTBEGIN Anchor the start of the cut block at the character associated with the routing key (see ``Cut and Paste'' for full details). This command clears the cut buffer. CUTAPPEND Anchor the start of the cut block at the character associated with the routing key (see ``Cut and Paste'' for full details). This command doesn't clear the cut buffer. CUTRECT Anchor the end of the cut block at the character associated with the routing key, and append the rectangular region to the cut buffer (see ``Cut and Paste'' for full details). CUTLINE Anchor the end of the cut block at the character associated with the routing key, and append the linear region to the cut buffer (see ``Cut and Paste'' for full details). COPYCHARS Copy the character block anchored by the two routing keys to the cut buffer (see ``Cut and Paste'' for full details). APNDCHARS Append the character block anchored by the two routing keys to the cut buffer (see ``Cut and Paste'' for full details). PRINDENT/NXINDENT Go up/down to the nearest line which isn't indented more than the column associated with the routing key. DESCCHAR Momentarily (see the ``-M'' command line option) display a message describing the character associated with the routing key. It reveals the decimal and hexadecimal values of the character, the foreground and background colours, and, when present, special attributes (bright and blink). The message looks like this: char 65 (0x41): white on black bright blink SETLEFT Horizontally reposition the braille window so that its left edge is at the column associated with the routing key. This feature makes it very easy to put the window exactly where it's needed, and, therefore, for displays which have routing keys, almost eliminates the need for a lot of elementary window motion (like the ``CHRLT/CHRRT'' and ``HWINLT/HWINRT'' commands). PRDIFCHAR/NXDIFCHAR Go up/down to the nearest line which has a different character in the column associated with the routing key. 4.1.13. Base Commands SWITCHVT Switch to the virtual terminal whose number (counting from 1) matches that of the routing key. See also the ``SWITCHVT_PREV/SWITCHVT_NEXT'' virtual terminal switching commands. SETMARK Mark (remember) the current position of the braille window in a register associated with the routing key. See the ``GOTOMARK'' command. This feature only affects the current virtual terminal. GOTOMARK Move the braille window to the position formerly marked (see the ``SETMARK'' command) with the same routing key. This feature only affects the current virtual terminal. 4.2. The Configuration File System defaults for many settings may be established within a configuration file. The default name for this file is /etc/brltty.conf, although it may be overridden with the ``-f'' command line option. It doesn't need to exist. A template for it can be found within the Documents subdirectory. Blank lines are ignored. A comment begin with a number sign (#), and continues to the end of the line. The following directives are recognized: api-parameters name=value,... Specify parameters for the Application Programming Interface. If the same parameter is specified more than once, then its rightmost assignment is used. For a description of the parameters accepted by the interface, please see the BrlAPI reference manual. See the ``--with-api-parameters'' build option for the defaults established during the build procedure. This directive can be overridden with the ``-A'' command line option. attributes-table file Specify the attributes table (see section ``Attributes Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with-execute-root'' build options for more details). The .atb extension is optional. The default is to use the built-in table (see the ``--with-attributes-table'' build option). This directive can be overridden with the ``-a'' command line option. braille-device device,... Specify the device to which the braille display is connected (see section ``Braille Device Specification''). See the ``--with-braille-device'' build option for the default established during the build procedure. This directive can be overridden with the ``-d'' command line option. braille-driver driver,...|auto Specify the braille display driver (see section ``Driver Specification''). The default is to perform autodetection. This directive can be overridden with the ``-b'' command line option. braille-parameters [driver:]name=value,... Specify parameters for the braille display drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``--with-braille-parameters'' build option for the defaults established during the build procedure. This directive can be overridden with the ``-B'' command line option. contraction-table file Specify the contraction table (see section ``Contraction Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with-execute-root'' build options for more details). The .ctb extension is optional. The contraction table is used when the 6-dot braille feature is activated (see the ``SIXDOTS'' command and the ``Text Style'' preference). The default is to display uncontracted 6-dot braille. This directive can be overridden with the ``-c'' command line option. It isn't available if the ``--disable-contracted-braille'' build option was specified. keyboard-table file|auto Specify the keyboard table (see section ``Key Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with- execute-root'' build options for more details). The .ktb extension is optional. The default is not to use a keyboard table. This directive can be overridden with the ``-k'' command line option. keyboard-properties name=value,... Specify the properties of the keyboard(s) to be monitored. If the same property is specified more than once, then its rightmost assignment is used. See section ``Keyboard Properties'' for a list of the properties which may be specified. The default is to monitor all keyboards. This directive can be overridden with the ``-K'' command line option. midi-device device Specify the device to use for the Musical Instrument Digital Interface (see section ``MIDI Device Specification''). This directive can be overridden with the ``-m'' command line option. It isn't available if the ``--disable-midi-support'' build option was specified. pcm-device device Specify the device to use for digital audio (see section ``PCM Device Specification''). This directive can be overridden with the ``-p'' command line option. It isn't available if the ``--disable-pcm-support'' build option was specified. preferences-file file Specify the location of the file which is to be used for the saving and loading of user preferences. If a relative path is supplied, then it's anchored at /var/lib/brltty. The default is to use brltty.prefs. This directive can be overridden with the ``-F'' command line option. release-device boolean Whether or not to release the device to which the braille display is connected when the current screen or window can't be read. on Release the device. off Don't release the device. The default setting is on on Windows platforms and off on all other platforms. This directive can be overridden with the ``-r'' command line option. screen-driver driver Specify the screen driver (see section ``Supported Screen Drivers''). See the ``--with-screen-driver'' build option for the default established during the build procedure. This directive can be overridden with the ``-x'' command line option. screen-parameters [driver:]name=value,... Specify parameters for the screen drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Supported Screen Drivers'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``--with-screen-parameters'' build option for the defaults established during the build procedure. This directive can be overridden with the ``-X'' command line option. speech-driver driver,...|auto Specify the speech synthesizer driver (see section ``Driver Specification''). The default is to perform autodetection. This directive can be overridden with the ``-s'' command line option. It isn't available if the ``--disable-speech-support'' build option was specified. speech-input name Specify the name of the file system object (FIFO, named pipe, named socket, etc) which can be used by other applications for text-to-speech conversion via BRLTTY's speech driver. This directive can be overridden with the ``-i'' command line option. It isn't available if the ``--disable-speech-support'' build option was specified. speech-parameters [driver:]name=value,... Specify parameters for the speech synthesizer drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``--with-speech-parameters'' build option for the defaults established during the build procedure. This directive can be overridden with the ``-S'' command line option. text-table file|auto Specify the text table (see section ``Text Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with- execute-root'' build options for more details). The .ttb extension is optional. The default is to perform locale-based autoselection, with fallback to the built-in table (see the ``--with-text-table'' build option). This directive can be overridden with the ``-t'' command line option. 4.3. Command Line Options Many settings can be explicitly specified when invoking BRLTTY. The brltty command accepts the following options: -afile --attributes-table=file Specify the attributes table (see section ``Attributes Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with-execute-root'' build options for more details). The .atb extension is optional. See the ``attributes-table'' configuration file directive for the default run-time setting. This setting can be changed with the ``Attributes Table'' preference. -bdriver,...|auto --braille-driver=driver,...|auto Specify the braille display driver (see section ``Driver Specification''). See the ``braille-driver'' configuration file directive for the default run-time setting. -cfile --contraction-table=file Specify the contraction table (see section ``Contraction Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with-execute-root'' build options for more details). The .ctb extension is optional. The contraction table is used when the 6-dot braille feature is activated (see the ``SIXDOTS'' command and the ``Text Style'' preference). See the ``contraction-table'' configureation file directive for the default run-time setting. This setting can be changed with the ``Contraction Table'' preference. This option isn't available if the ``--disable-contracted-braille'' build option was specified. -ddevice,... --braille-device=device,... Specify the device to which the braille display is connected (see section ``Braille Device Specification''). See the ``braille-device'' configuration file directive for the default run-time setting. -e --standard-error Write diagnostic messages to standard error. The default is to record them via syslog. -ffile --configuration-file=file Specify the location of the ``configuration file'' which is to be used for the establishing of default run-time settings. -h --help Display a summary of the command line options accepted by BRLTTY, and then exit. -iname --speech-input=name Specify the name of the file system object (FIFO, named pipe, named socket, etc) which can be used by other applications for text-to-speech conversion via BRLTTY's speech driver. If not specified, the file system object is not created. See the ``speech-input'' configuration file directive for the default run-time setting. This option isn't available if the ``--disable-speech-support'' build option was specified. -kfile --keyboard-table=file Specify the keyboard table (see section ``Key Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with- execute-root'' build options for more details). The .ktb extension is optional. See the ``keyboard-table'' configureation file directive for the default run-time setting. This setting can be changed with the ``Keyboard Table'' preference. -llevel --log-level=level Specify the severity threshold for diagnostic message generation. The following levels are recognized. 0 emergency 1 alert 2 critical 3 error 4 warning 5 notice 6 information 7 debug Either the number or the name may be supplied, and the name may be abbreviated. If not specified, then information is assumed (see the ``-q'' option for more details). -mdevice --midi-device=device Specify the device to use for the Musical Instrument Digital Interface (see section ``MIDI Device Specification''). See the ``midi-device'' configuration file directive for the default run-time setting. This option isn't available if the ``--disable-midi-support'' build option was specified. -n --no-daemon Specify that BRLTTY is to remain in the foreground. If not specified, then BRLTTY becomes a background process (daemon) after initializing itself but before starting any of the selected drivers. -pdevice --pcm-device=device Specify the device to use for digital audio (see section ``PCM Device Specification''). See the ``pcm-device'' configuration file directive for the default run-time setting. This option isn't available if the ``--disable-pcm-support'' build option was specified. -q --quiet Log less information. This option changes the default log level (see the ``-l'' option) to notice if either the ``-v'' or the ``-V'' option is specified, and to warning otherwise. -r --release-device Release the device to which the braille display is connected when the current screen or window can't be read. See the ``release-device'' configuration file directive for the default run-time setting. -sdriver,...|auto --speech-driver=driver,...|auto Specify the speech synthesizer driver (see section ``Driver Specification''). See the ``speech-driver'' configuration file directive for the default run-time setting. This option isn't available if the ``--disable-speech-support'' build option was specified. -tfile --text-table=file Specify the text table (see section ``Text Tables'' for details). If a relative path is supplied, then it's anchored at /etc/brltty (see the ``--with-data-directory'' and the ``--with- execute-root'' build options for more details). The .ttb extension is optional. See the ``text-table'' configureation file directive for the default run-time setting. This setting can be changed with the ``Text Table'' preference. -v --verify Display the current versions of BRLTTY itself, of the server side of its application programming interface, and of the selected braille and speech drivers, and then exit. If the ``-q'' option isn't specified, then also display the values of the options after all sources have been considered. If more than one braille driver (see the ``-b'' command line option) and/or more than one braille device (see the ``-d'' command line option) has been specified then braille display autodetection is performed. If more than one speech driver (see the ``-s'' command line option) has been specified then speech synthesizer autodetection is performed. -xdriver --screen-driver=driver Specify the screen driver (see section ``Supported Screen Drivers''). See the ``screen-driver'' configuration file directive for the default run-time setting. -Aname=value,... --api-parameters=name=value,... Specify parameters for the Application Programming Interface. If the same parameter is specified more than once, then its rightmost assignment is used. For a description of the parameters accepted by the interface, please see the BrlAPI reference manual. See the ``api-parameters'' configuration file directive for the default run-time settings. -B[driver:]name=value,... --braille-parame- ters=[driver:]name=value,... Specify parameters for the braille display drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``braille-parameters'' configuration file directive for the default run-time settings. -E --environment-variables Recognize environment variables when determining the default settings for unspecified command line options (see section ``Command Line Options''). If this option is specified, and if the environment variable associated with an unspecified option is defined, then the value of that environment variable is used. The names of these environment variables are based on the long names of the options they correspond to: · All letters are in upper case. · Underscores (_) are used instead of minus signs (-). · The prefix BRLTTY_ is added. This option is particularly useful on the Linux operating system as it allows default settings to be passed to BRLTTY via boot parameters. The following environment variables are supported: BRLTTY_API_PARAMETERS Parameters for the Application Programming Interface (see the ``-A'' command line option). BRLTTY_ATTRIBUTES_TABLE The attributes table (see the ``-a'' command line option). BRLTTY_BRAILLE_DEVICE The braille display device (see the ``-d'' command line option). BRLTTY_BRAILLE_DRIVER The braille display driver (see the ``-b'' command line option). BRLTTY_BRAILLE_PARAMETERS Parameters for the braille display driver (see the ``-B'' command line option). BRLTTY_CONFIGURATION_FILE The configuration file (see the ``-f'' command line option). BRLTTY_CONTRACTION_TABLE The contraction table (see the ``-c'' command line option). BRLTTY_KEYBOARD_TABLE The keyboard table (see the ``-k'' command line option). BRLTTY_KEYBOARD_PROPERTIES The keyboard properties (see the ``-K'' command line option). BRLTTY_MIDI_DEVICE The Musical Instrument Digital Interface device (see the ``-m'' command line option). BRLTTY_PCM_DEVICE The digital audio device (see the ``-p'' command line option). BRLTTY_PREFERENCES_FILE The location of the file which is to be used for the saving and loading of user preferences (see the ``-F'' command line option). BRLTTY_RELEASE_DEVICE Whether or not to release the device to which the braille display is connected when the current screen or window can't be read (see the ``-r'' command line option). BRLTTY_SCREEN_PARAMETERS Parameters for the screen driver (see the ``-X'' command line option). BRLTTY_SPEECH_DRIVER The speech synthesizer driver (see the ``-s'' command line option). BRLTTY_SPEECH_INPUT The name of the file system object which can be used by other applications for text-to-speech conversion via BRLTTY's speech driver (see the ``-i'' command line option). BRLTTY_SPEECH_PARAMETERS Parameters for the speech synthesizer driver (see the ``-S'' command line option). BRLTTY_TEXT_TABLE The text table (see the ``-t'' command line option). -Ffile --preferences-file=file Specify the location of the file which is to be used for the saving and loading of user preferences. If a relative path is supplied, then it's anchored at /var/lib/brltty. See the ``preferences-file'' configuration file directive for the default run-time setting. -I --install-service Install BRLTTY as the BrlAPI service. This means that: · BRLTTY will be automatically started when the system is booted. · Applications can know that a BrlAPI server is running. This option is only supported on the Windows platform. -Kname=value,... --keyboard-properties=name=value,... Specify the properties of the keyboard(s) to be monitored. If the same property is specified more than once, then its rightmost assignment is used. See section ``Keyboard Properties'' for a list of the properties which may be specified. See the ``keyboard-properties'' configuration file directive for the default run-time settings. -Mcsecs --message-timeout=csecs Specify the amount of time (in hundredths of a second) that BRLTTY keeps its own internally generated messages on the braille display. If not specified, then 400 (4 seconds) is assumed. -N --no-api Disable the application programming interface. -Pfile --pid-file=file Specify the file wherein BRLTTY is to write its process identifier (pid). If not specified, BRLTTY doesn't write its process identifier anywhere. -R --remove-service Remove the BrlAPI service. This means that: · BRLTTY will not be automatically started when the system is booted. · Applications can know that no BrlAPI server is running. This option is only supported on the Windows platform. -S[driver:]name=value,... --speech-parame- ters=[driver:]name=value,... Specify parameters for the speech synthesizer drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Driver Identification Codes'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``speech-parameters'' configuration file directive for the default run-time settings. -V --version Display the current versions of BRLTTY itself, of the server side of its application programming interface, and of those drivers which have been linked into its binary, and then exit. If the ``-q'' option isn't specified, then also display copyright information. -X[driver:]name=value,... --screen-parame- ters=[driver:]name=value,... Specify parameters for the screen drivers. If the same parameter is specified more than once, then its rightmost assignment is used. If a parameter name is qualified by a driver (see section ``Supported Screen Drivers'') then that setting only applies to that driver; if it isn't then it applies to all drivers. For a description of the parameters accepted by a specific driver, please see the documentation for that driver. See the ``screen-parameters'' configuration file directive for the default run-time settings. 5. Feature Descriptions 5.1. Cursor Routing When moving the braille window around the screen while examining the text, say, in an editor, you often need to bring the cursor to a specific character within the braille window. You'll probably find this to be a rather difficult task for a number of reasons. One is that you may not know where the cursor is, and that you may lose your place while trying to find it. Another is that the cursor may move unpredictably as the arrow keys are pressed (some editors, for example, don't allow the cursor to be more to the right than the end of the line it's on). Cursor routing provides just such a capability by knowing where the cursor is, by simulating the same arrow-key presses which you'd have to enter manually, and by monitoring the progress of the cursor as it moves. Some braille displays have a button, known as a routing key, above each cell. These keys use the ``ROUTE'' command to route the cursor right to the desired location. Cursor routing, while very convenient and effective, is, strictly speaking, not completely reliable. One reason for this is that its current implementation assumes VT100 cursor key escape sequences. Another is that some applications do non-standard things in response to detecting that a cursor key has been pressed. A minor problem found within some editors (like vi), as already mentioned above, is that they throw in some unpredictable horizontal motion when vertical motion is requested because they don't allow the cursor to be to the right of the end of a line. A major problem found within some web browsers (like lynx) is that the up- and down-arrow keys are used to move among the links (which may skip lines and/or move the cursor horizontally, but which rarely just moves the cursor one line in the desired direction), and that the left- and right-arrow keys are used to select links (which has absolutely nothing to do with any form of cursor motion whatsoever, and which even totally changes the screen content). Cursor routing may not work very well on a heavily loaded system, and definitely doesn't work very well when working on a remote system over a slow link. This is so because of all of the checks which must be made along the way in order to deal with unpredictable cursor motion and in order to ensure that any mistake has at least a fighting chance to be undone. Even though BRLTTY tries to be fairly clever, it must still essentially wait to see what happens after each simulated arrow- key press. Once a cursor routing request has been made, BRLTTY keeps trying to route the cursor to the desired location until a timeout expires before the cursor reaches that location, the cursor seems to be moving in the wrong direction, or you switch to a different virtual terminal. An attempt is first made to use vertical motion to bring the cursor to the right line, and, only if that succeeds, an attempt is then made to use horizontal motion to bring the cursor to the right column. If another request is made while one is still in progress, then the first one is aborted and the second one is initiated. A safer but less powerful cursor routing command, ``CSRJMP_VERT'', uses just vertical motion to bring the cursor to anywhere on the top line of the braille window. It's especially useful in conjunction with applications (like lynx) wherein horizontal cursor motion must never be attempted. 5.2. Cut and Paste This feature enables you to grab some text which is already on the screen and re-enter it at the current cursor position. Using it saves time and avoids errors when a long and/or complicated piece of text needs to be copied, and even when the same short and simple piece of text needs to be copied many times. It's particularly useful for things like long file names, complicated command lines, E-mail addresses, and URLs. Cutting and pasting text involves three simple steps: 1. Mark either the top-left corner of the rectangular area or the beginning of the linear area on the screen which is to be grabbed (cut). If your display has routing keys, then move the braille window so that the first character to be cut appears anywhere within it, and then: · invoke the ``CUTBEGIN'' command to start a new cut buffer · invoke the ``CUTAPPEND'' command to append to the existing cut buffer by pressing the key(s) associated with it and then pressing the routing key associated with the character. 2. Mark either the bottom-right corner of the rectangular area or the end of the linear area on the screen which is to be grabbed (cut). If your display has routing keys, then move the braille window so that the last character to be cut appears anywhere within it, and then · invoke the ``CUTRECT'' command to cut a rectangular area · invoke the ``CUTLINE'' command to cut a linear area by pressing the key(s) associated with it and then pressing the routing key associated with the character. Marking the end of the cut area appends the selected screen content to the cut buffer. Excess white-space is removed from the end of each line in the cut buffer so that unwanted trailing spaces won't be pasted back in. Control characters are replaced with blanks. 3. Insert (paste) the text where it's needed. Place the cursor over the character where the text is to be pasted, and invoke the ``PASTE'' command. You can paste the same text any number of times without recutting it. This description assumes that you're already in some sort of input mode. If you paste when you're in some other kind of mode (like vi's command mode), then you'd better be aware of what the characters in the cut buffer will do. The cut buffer is also used by the ``PRSEARCH/NXSEARCH'' commands. 5.3. Pointer (Mouse) Support via GPM If BRLTTY is configured with the ``--enable-gpm'' build option on a system where the gpm application has been installed, then it'll interact with the pointer (mouse). Moving the pointer drags the braille window (see the ``Window Follows Pointer'' preference). Whenever the pointer is moved beyond the edge of the braille window, the braille window is dragged along (one character at a time). This gives the braille user another two- dimensional way to inspect the screen content or to quickly move the braille window to a desired location. It also gives a sighted observer an easy way to move the braille window to something he'd like the braille user to read. gpm uses reverse video to show where the pointer is. Underlining of highlighted characters (see the ``ATTRVIS'' command for details) should be turned on, therefore, when the braille user wishes to use the pointer. This feature also gives the braille user access to gpm's cut-and-paste capability. Although you should read gpm's own documentation, here are some notes on how it works. · Copy the current character to the cut buffer by single-clicking the left button. · Copy the current word (space-delimited) to the cut buffer by double-clicking the left button. · Copy the current line to the cut buffer by tripple-clicking the left button. · Copy a linear region to the cut buffer as follows: 1. Place the pointer on the first character of the region. 2. Press (and hold) the left button. 3. Move the pointer to the last character of the region (all currently selected characters are highlighted). 4. Release the left button. · Paste (input) the current contents of the cut buffer by clicking the middle button of a three-button mouse or by clicking the right button of a two-button mouse. · Append to the cut buffer by using the right button of a three- button mouse. 5.4. Alert Tunes BRLTTY alerts you to the occurrence of significant events by playing short predefined tunes. This feature can be activated and deactivated with either the ``TUNES'' command or the ``Alert Tunes'' preference. The tunes are played via the internal beeper by default, but other alternatives can be selected with the ``Tune Device'' preference. Each significant event is associated, from highest to lowest priority, with one or more of the following: a tune If a tune has been associated with the event, if the ``Alert Tunes'' preference (see also the ``TUNES'' command) is active, and if the selected tune device (see the ``Tune Device'' preference) can be opened, then the tune is played. a dot pattern If a dot pattern has been associated with the event, and if the ``Alert Dots'' preference is active, then the dot pattern is briefly displayed on every braille cell. Some braille displays don't respond quickly enough for this mechanism to work effectively. a message If a message has been associated with the event, and if the ``Alert Messages'' preference is active, then it is displayed for a few seconds (see the ``-M'' command line option). These events include: · When the braille display driver starts or stops. · When a lengthy command completes. · When a command cannot be executed. · When a mark is set. · When the start or end of the cut block is set. · When a feature is activated or deactivated. · When cursor tracking is turned on or off. · When the screen image is frozen or unfrozen. · When the braille window wraps either down to the beginning of the next line or up to the end of the previous line. · When identical lines are skipped. · When a requested motion cannot be performed. · When cursor routing starts, finishes, or fails. 5.5. Preferences Settings When BRLTTY starts, it loads a file which contains your preferences settings. The file doesn't need to exist, and is created the first time the settings are saved with the ``PREFSAVE'' command. The most recently saved settings can be restored at any time with the ``PREFLOAD'' command. The name for this file is /etc/brltty-driver.prefs. where driver is the two-letter ``driver identification code''. 5.5.1. The Preferences Menu The preferences settings are saved as binary data which, therefore, can't be edited by hand. BRLTTY, however, has a simple menu from which you can easily change them. The menu is activated by the ``PREFMENU'' command. The braille display briefly (see the ``-M'' command line option) shows the menu title, and then presents the current item and its current setting. 5.5.1.1. Navigating the Menu See ``Menu Navigation Commands'' for the full list of commands which enable you to select items and change settings within the menu. For backward compatibility with old drivers, the window motion commands, which have modified meanings in this context, can also be used. TOP/BOT, TOP_LEFT/BOT_LEFT, PAGE_UP/PAGE_DOWN Go to the first/last item in the menu (same as ``MENU_FIRST_ITEM/MENU_LAST_ITEM''). LNUP/LNDN, PRDIFLN/NXDIFLN, CURSOR_UP/CURSOR_DOWN Go to the previous/next item in the menu (same as ``MENU_PREV_ITEM/MENU_NEXT_ITEM''). WINUP/WINDN, CHRLT/CHRRT, CURSOR_LEFT/CURSOR_RIGHT, BACK/HOME Decrement/increment the current menu item's setting (same as ``MENU_PREV_SETTING/MENU_NEXT_SETTING''). Notes: · The routing keys can also be used to select a setting for the current item. If the item has numeric settings, then the entire row of routing keys acts as a scroll bar which covers the full range of valid values. If the item has named settings, then the routing keys correspond ordinally with the settings. · Use the PREFLOAD command to undo all of the changes which were made since entering the menu. · Use the PREFMENU command (again) to leave the new settings in effect, exit the menu, and resume normal operation. If the "Save Settings on Exit" item is set, then, in addition, the new settings are written to the preferences settings file. Any command not recognized by the menu system also does these same things. 5.5.1.2. The Menu Items Save on Exit When exiting the preferences menu: No Don't automatically save the preferences settings. Yes Automatically save the preferences settings. The initial setting is No. Text Style When displaying screen content (see the ``DISPMD'' command), show characters: 8-dot With all eight dots. 6-dot With only dots 1 through 6. If a contraction table has been selected (see the ``-c'' command line option and the ``contraction-table'' configuration file directive), then it is used. This setting can also be changed with the ``SIXDOTS'' command. Skip Identical Lines When moving either up or down exactly one line with the ``LNUP/LNDN'' commands, as well as the line wrapping feature of the ``FWINLT/FWINRT'' and ``FWINLTSKIP/FWINRTSKIP'' commands: No Don't skip past lines which have the same content as the current line. Yes Skip past lines which have the same content as the current line. This setting can also be changed with the ``SKPIDLNS'' command. Skip Blank Windows When moving either left or right with the ``FWINLT/FWINRT'' commands: No Don't skip past blank windows. Yes Skip past blank windows. This setting can also be changed with the ``SKPBLNKWINS'' com- mand. Which Blank Windows If blank windows are to be skipped: All Skip all of them. End of Line Only skip those which are at the end (on the right side) of a line. Rest of Line Only skip those which are at the end (on the right side) of a line when reading forward, and at the beginning (on the left side) of a line when reading backward. Sliding Window If the cursor is being tracked (see the ``CSRTRK'' command), and the cursor moves too close to (or beyond) either end of the braille window: No Horizontally reposition the window such that its left end is a multiple of its width from the left edge of the screen. Yes Horizontally reposition the window such that the cursor, while remaining on that side of the window, is nearer the centre. This setting can also be changed with the ``SLIDEWIN'' command. Eager Sliding Window If the braille window is to slide: No Reposition it whenever the cursor moves beyond either end. Yes Reposition it whenever the cursor moves too close to either end. The initial setting is No. Window Overlap When moving either left or right with the ``FWINLT/FWINRT'' commands, this setting specifies how many characters horizontally adjacent braille windows should overlap each other by. The initial setting is 0. Autorepeat While the key (combination) for a command remains pressed: No Don't automatically repeat the command. Yes Automatically repeat the command at a regular interval after an initial delay. The following commands are eligible for autorepeating: · The ``LNUP/LNDN'' commands. · The ``PRDIFLN/NXDIFLN'' commands. · The ``CHRLT/CHRRT'' commands. · Braille window panning operations (see the ``Autorepeat Panning'' preference). · The Page-Up and Page-Down operations. · The Cursor-Up and Cursor-Down operations. · The Cursor-Left and Cursor-Right operations. · The Backspace and Delete operations. · Character entry. Only some drivers support this functionality, the primary limi- tation being that many braille displays don't signal both key presses and key releases as distinctly separate events. This setting can also be changed with the ``AUTOREPEAT'' command. The initial setting is Yes. Autorepeat Panning When the ``Autorepeat'' preference is enabled: No Don't autorepeat braille window panning operations. Yes Autorepeat braille window panning operations. This preference affects the ``FWINLT/FWINRT'' commands. The initial setting is No. Autorepeat Delay When a character is to be autorepeated, this setting specifies the amount of time (see the note on ``time settings'' below) which must pass before autorepeating begins. The initial setting is 50. Autorepeat Interval When a character is being autorepeated, this setting specifies the amount of time (see the note on ``time settings'' below) between each reexecution. The initial setting is 10. Show Cursor When displaying screen content (see the ``DISPMD'' command): No Don't show the cursor. Yes Show the cursor. This setting can also be changed with the ``CSRVIS'' command. The initial setting is Yes. Cursor Style When showing the cursor, represent it: Underline With dots 7 and 8. Block With all eight dots. This setting can also be changed with the ``CSRSIZE'' command. Blinking Cursor When the cursor is to be shown: No Leave it visible all the time. Yes Make it alternately visible and invisible according to a predefined interval. This setting can also be changed with the ``CSRBLINK'' command. Cursor Visible Time When the cursor is to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that it is to be visible. The initial setting is 40. Cursor Invisible Time When the cursor is to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that it is to be invisible. The initial setting is 40. Show Attributes When displaying screen content (see the ``DISPMD'' command): No Don't underline highlighted characters. Yes Underline highlighted characters. This setting can also be changed with the ``ATTRVIS'' command. Blinking Attributes When highlighted characters are to be underlined: No Leave the indicator visible all the time. Yes Make the indicator alternately visible and invisible according to a predefined interval. This setting can also be changed with the ``ATTRBLINK'' command. Attributes Visible Time When the highlighted character underline is to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that it is to be visible. The initial setting is 20. Attributes Invisible Time When the highlighted character underline is to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that it is to be invisible. The initial setting is 60. Blinking Capitals When displaying screen content (see the ``DISPMD'' command): No Leave capital letters visible all the time. Yes Make capital letters alternately visible and invisible according to a predefined interval. This setting can also be changed with the ``CAPBLINK'' command. Capitals Visible Time When capital letters are to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that they're to be visible. The initial setting is 60. Capitals Invisible Time When capital letters are to be blinked, this setting specifies the length of time (see the note on ``time settings'' below) during each cycle that they're to be invisible. The initial setting is 20. Braille Firmness Adjust the firmness (or stiffness) of the braille dots. It can be set to: · Maximum · High · Medium · Low · Minimum This preference is only available if a driver which supports it is being used. The initial setting is Medium. Braille Sensitivity Adjust the sensitivity of the braille dots to touch. It can be set to: · Maximum · High · Medium · Low · Minimum This preference is only available if a driver which supports it is being used. The initial setting is Medium. Window Follows Pointer When moving the pointer device (mouse): No Don't drag the braille window. Yes Drag the braille window. This preference is only presented if the ``--enable-gpm'' build option was specified. Highlight Window When moving the braille window: No Don't highlight the new screen area. Yes Highlight the new screen area. This feature enables a sighted observer to see where the braille window is, and, therefore, to know what the braille user is reading. Any motion of the braille window (manual, cursor tracking, etc.), other than when it moves in response to pointer (mouse) motion (see the ``Window Follows Pointer'' preference), causes the area of the screen corresponding to the new location of the braille window to be highlighted. If the ``Show Attributes'' preference is enabled then only the character cor- responding to the upper-left corner of the braille window is highlighted. Alert Tunes Whenever a significant event with an associated tune occurs (see ``Alert Tunes''): No Don't play the tune. Yes Play the tune. This setting can also be changed with the ``TUNES'' command. The initial setting is Yes. Tune Device Play alert tunes via: Beeper The internal beeper (console tone generator). This setting is supported on Linux, on OpenBSD, on FreeBSD, and on NetBSD. It's always safe to use, although it may be somewhat soft. This device isn't available if the ``--disable-beeper- support'' build option was specified. PCM The digital audio interface on the sound card. This setting is supported on Linux (via /dev/dsp), on Solaris (via /dev/audio), on OpenBSD (via /dev/audio0), on FreeBSD (via /dev/dsp), and on NetBSD (via /dev/audio0). It doesn't work when this device is already being used by another application. This device isn't available if the ``--disable- pcm-support'' build option was specified. MIDI The Musical Instrument Digital Interface on the sound card This setting is supported on Linux (via /dev/sequencer). It doesn't work when this device is already being used by another application. This device isn't available if the ``--disable-midi-support'' build option was specified. FM The FM synthesizer on an AdLib, OPL3, Sound Blaster, or equivalent sound card. This setting is supported on Linux. It works even if the FM synthesizer is already being used by another application. The results are unpredictable, and potentially not very good, if it's used with a sound card which doesn't support this feature. This device isn't available if the ``--disable-fm-support'' build option was specified. The initial setting is Beeper on those platforms which support it, and PCM on those platforms which don't. PCM Volume If the digital audio interface of the sound card is being used to play the alert tunes, this setting specifies the loudness (as a percentage of the maximum) at which they are to be played. The initial setting is 70. MIDI Volume If the Musical Instrument Digital Interface (MIDI) of the sound card is being used to play the alert tunes, this setting specifies the loudness (as a percentage of the maximum) at which they are to be played. The initial setting is 70. MIDI Instrument If the Musical Instrument Digital Interface (MIDI) of the sound card is being used to play the alert tunes, this setting specifies which instrument is to be used (see the ``MIDI Instrument Table''). The initial setting is Acoustic Grand Piano. FM Volume If the FM synthesizer of the sound card is being used to play the alert tunes, this setting specifies the loudness (as a percentage of the maximum) at which they are to be played. The initial setting is 70. Alert Dots Whenever a significant event with an associated dot pattern occurs (see ``Alert Tunes''): No Don't display the dot pattern. Yes Briefly display the dot pattern. If alert tunes are to be played (see the ``TUNES'' command and the ``Alert Tunes'' preference), if a tune has been associated with the event, and if the selected tune device can be opened, then, regardless of the setting of this preference, the dot pat- tern isn't displayed. Alert Messages Whenever a significant event with an associated message occurs (see ``Alert Tunes''): No Don't display the message. Yes Display the message. If alert tunes are to be played (see the ``TUNES'' command and the ``Alert Tunes'' preference), if a tune has been associated with the event, and if the selected tune device can be opened, or if alert dot patterns are to be displayed (see the ``Alert Dots'' preference) and if a dot pattern has been associated with the event, then, regardless of the setting of this preference, the message isn't displayed. Say-Line Mode When using the ``SAY_LINE'' command: Immediate Discard pending speech. Enqueue Don't discard pending speech. The initial setting is Immediate. Autospeak No Only speak when explicitly requested to do so. Yes Automatically speak: · the new line when the braille window is moved vertically. · characters which are entered or deleted. · the character to which the cursor is moved. This setting can also be changed with the ``AUTOSPEAK'' command. The initial setting is No. Speech Rate Adjust the speech rate (0 is the slowest, 20 is the fastest). This preference is only available if a driver which supports it is being used. This setting can also be changed with the ``SAY_SLOWER/SAY_FASTER'' commands. The initial setting is 10. Speech Volume Adjust the speech volume (0 is the softest, 20 is the loudest). This preference is only available if a driver which supports it is being used. This setting can also be changed with the ``SAY_SOFTER/SAY_LOUDER'' commands. The initial setting is 10. Speech Pitch Adjust the speech pitch (0 is the lowest, 20 is the highest). This preference is only available if a driver which supports it is being used. The initial setting is 10. Speech Punctuation Adjust the amount of punctuation which is spoken. It can be set to: · None · Some · All This preference is only available if a driver which supports it is being used. The initial setting is Some. Status Style This setting specifies the way that the status cells are to be used. You shouldn't normally need to play with it. It enables BRLTTY's developers to test status cell configurations for braille displays which they don't actually have. None Don't use the status cells. This setting is always safe, but it's also quite useless. Alva The status cells contain: 1 The location of the cursor (see below). 2 The location of the top-left corner of the braille window (see below). 3 A letter indicating BRLTTY's state. In order of precedence: a Screen attributes are being shown (see the ``DISPMD'' command). f The screen image is frozen (see the ``FREEZE'' command). f The cursor is being tracked (see the ``CSRTRK'' command). blank Nothing special. The locations of the cursor and the braille window are pre- sented in an interesting way. Dots 1 through 6 represent the line number with a letter from a (for 1) through y (for 25). Dots 7 and 8 (the extra two at the bottom) represent the hor- izontal braille window number as follows: No Dots The first (leftmost) window. Dot 7 The second window. Dot 8 The third window. Dots 7 and 8 The fourth window. In both cases, the indicators wrap: line 26 is represented by the letter a, and the fifth horizontal braille window is rep- resented by no dots at the bottom. Tieman The status cells contain: 1-2 The columns (counting from 1) of the cursor (shown in the top half of the cells) and the top-left corner of the braille window (shown in the bottom half of the cells). 3-4 The rows (counting from 1) of the cursor (shown in the top half of the cells) and the top-left corner of the braille window (shown in the bottom half of the cells). 5 Each dot indicates if a feature is turned on as follows: Dot 1 The screen image is frozen (see the ``FREEZE'' command). Dot 2 Screen attributes are being displayed (see the ``DISPMD'' command). Dot 3 Alert tunes are being played (see the ``TUNES'' command). Dot 4 The cursor is being shown (see the ``CSRVIS'' command). Dot 5 The cursor is a solid block (see the ``CSRSIZE'' command). Dot 6 The cursor is blinking (see the ``CSRBLINK'' command). Dot 7 The cursor is being tracked (see the ``CSRTRK'' command). Dot 8 The braille window will slide (see the ``SLIDEWIN'' command). PowerBraille 80 The status cells contain: 1 The row (counting from 1) corresponding to the top of the braille window. The tens digit is shown in the top half of the cell, and the units digit is shown in the bottom half of the cell. Generic This setting passes a lot of information to the braille driver, and the driver itself decides how to present it. MDV The status cells contain: 1-2 The location of the top-left corner of the braille window. The row (counting from 1) is shown in the top half of the cells, and the column (counting from 1) is shown in the bottom half of the cells. Voyager The status cells contain: 1 The row (counting from 1) corresponding to the top of the braille window (see below). 2 The row (counting from 1) whereon the cursor is (see below). 3 If the screen is frozen (see the ``FREEZE'' command), then the letter F. If it isn't, then the column (counting from 1) wherein the cursor is (see below). Row and column numbers are shown as two digits within a sin- gle cell. The tens digit is shown in the top half of the cell, and the units digit is shown in the bottom half of the cell. The initial setting is braille display driver dependent. Text Table Select the text table. See section ``Text Tables'' for details. See the ``-t'' command line option for the initial setting. This preference isn't saved. Attributes Table Select the attributes table. See section ``Attributes Tables'' for details. See the ``-a'' command line option for the initial setting. This preference isn't saved. Contraction Table Select the contraction table. See section ``Contraction Tables'' for details. See the ``-c'' command line option for the initial setting. This preference isn't saved. Keyboard Table Select the keyboard table. See section ``Key Tables'' for details. See the ``-k'' command line option for the initial setting. This preference isn't saved. Notes: · All time settings are in hundredths of a second. They are multiples of 4 within the range 1 through 100. 5.6. The Status Display The status display is a summary of BRLTTY's current state which fits completely within the braille window. Some braille displays have a set of status cells which are used to permanently display some of this information as well (see the documentation for your display's driver). The data presented by this display isn't static, and may change at any time in response to screen updates and/or BRLTTY commands. Use the ``INFO'' command to switch to the status display, and use it again to return to the screen. The layout of the information contained therein is dependent on the size of the braille window. 5.6.1. Displays with 21 Cells or More Short pneumonics have been used, even though they're rather cryptic, in order to show the precise column layout. wx:wy cx:cy vt tcmfdu wx:wy The column and row (counting from 1) on the screen corresponding to the top-left corner of the braille window. cx:cy The column and row (counting from 1) on the screen corresponding to the position of the cursor. vt The number (counting from 1) of the current virtual terminal. t The state of the cursor tracking feature (see the ``CSRTRK'' command). blank Cursor tracking is off. t Cursor tracking is on. c The state of the cursor visibility features (see the ``CSRVIS'' and ``CSRBLINK'' commands). blank The cursor isn't visible, and won't blink when made visible. b The cursor isn't visible, and will blink when made visible. v The cursor is visible, and isn't blinking. B The cursor is visible, and is blinking. m The current display mode (see the ``DISPMD'' command). t Screen content (text) is being displayed. a Screen highlighting (attributes) is being displayed. f The state of the frozen screen feature (see the ``FREEZE'' command). blank The screen isn't frozen. f The screen is frozen. d The number of braille dots being used to display each character (see the ``SIXDOTS'' command). 8 All eight dots are being used. 6 Only dots 1 through 6 are being used. u The state of the uppercase (capital letter) display features (see the ``CAPBLINK'' command). blank Uppercase letters don't blink. B Uppercase letters blink. 5.6.2. Displays with 20 Cells or Less Short pneumonics have been used, even though they're rather cryptic, in order to show the precise column layout. xxyys vt tcmfdu xx The columns (counting from 1) on the screen corresponding to the position of the cursor (shown in the top half of the cells) and to the top-left corner of the braille window (shown in the bottom half of the cells). yy The rows (counting from 1) on the screen corresponding to the position of the cursor (shown in the top half of the cells) and to the top-left corner of the braille window (shown in the bottom half of the cells). s The settings of some of BRLTTY's features. A feature is turned on if its corresponding dot is raised. Dot 1 Frozen screen image (see the ``FREEZE'' command). Dot 2 Display attributes (see the ``DISPMD'' command). Dot 3 Alert tunes (see the ``TUNES'' command). Dot 4 Visible cursor (see the ``CSRVIS'' command). Dot 5 Block cursor (see the ``CSRSIZE'' command). Dot 6 Blinking cursor (see the ``CSRBLINK'' command). Dot 7 Cursor tracking (see the ``CSRTRK'' command). Dot 8 Sliding window (see the ``SLIDEWIN'' command). vt The number (counting from 1) of the current virtual terminal. t The state of the cursor tracking feature (see the ``CSRTRK'' command). blank Cursor tracking is off. t Cursor tracking is on. c The state of the cursor visibility features (see the ``CSRVIS'' and ``CSRBLINK'' commands). blank The cursor isn't visible, and won't blink when made visible. b The cursor isn't visible, and will blink when made visible. v The cursor is visible, and isn't blinking. B The cursor is visible, and is blinking. m The current display mode (see the ``DISPMD'' command). t Screen content (text) is being displayed. a Screen highlighting (attributes) is being displayed. f The state of the frozen screen feature (see the ``FREEZE'' command). blank The screen isn't frozen. f The screen is frozen. d The number of braille dots being used to display each character (see the ``SIXDOTS'' command). 8 All eight dots are being used. 6 Only dots 1 through 6 are being used. u The state of the uppercase (capital letter) display features (see the ``CAPBLINK'' command). blank Uppercase letters don't blink. B Uppercase letters blink. 5.7. Command Learn Mode Command learn mode is an interactive way to learn what the keys on the braille display do. It can be accessed either by the ``LEARN'' command or via the ``brltest'' utility. This feature isn't available if the ``--disable-learn-mode'' build option was specified. When this mode is entered, the message command learn mode is written to the braille display. Then, as each key (or key combination) on the display is pressed, a short message describing its BRLTTY function is written. This mode exits immediately if the key (or key combination) for the ``LEARN'' command is pressed. It exits automatically, and the message done is written, if ten seconds elapse without any key on the display being pressed. Note that some displays don't signal the driver and/or some drivers don't signal BRLTTY until all the keys are released. If a message is longer than the braille display is wide, then it's displayed in segments. The length of each segment but the last is one less than the display's width, with the rightmost character on the display being set to a minus sign. Each such segment remains on the display either for a few seconds (see the ``-M'' command line option) or until any key on the display is pressed. 6. Tables 6.1. Text Tables Files with names of the form *.ttb are text tables, and with names of the form *.tti are text subtables. They are used by BRLTTY to translate the characters on the screen into their corresponding 8-dot computer braille representations. BRLTTY is initially configured to use the ``North American Braille Computer Code'' (NABCC) text table. In addition to this default, the following alternatives are provided: Name Language auto locale-based autoselection ar Arabic (generic) as Assamese awa Awadhi bg Bulgarian bh Bihari bn Bengali bo Tibetan bra Braj brf Braille Ready Format (for viewing .brf files within an editor or pager) cs Czech cy Welsh da Danish da-1252 Danish (Svend Thougaard, 2002-11-18) da-lt Danish (LogText) de German dra Dravidian el Greek en English en_CA English (Canada) en_GB English (United Kingdom) en_US English (United States) en-nabcc English (North American Braille Computer Code) eo Esperanto es Spanish et Estonian fi Finnish fr French fr_CA French (Canada) fr_FR French (France) fr-2007 French (unified 2007) fr-cbifs French (Code Braille Informatique Français Standard) fr-vs French (VisioBraille) ga Irish gd Gaelic gon Gondi gu Gujarati he Hebrew hi Hindi hr Croatian hu Hungarian hy Armenian is Icelandic it Italian kha Khasi kn Kannada kok Konkani kru Kurukh lt Lituanian lv Latvian mg Malagasy mi Maori ml Malayalam mni Manipuri mr Marathi mt Maltese mun Munda mwr Marwari ne Nepali new Newari nl Dutch nl_BE Dutch (Belgium) nl_NL Dutch (Netherlands) no Norwegian no-generic Norwegian (with support for other languages) no-oup Norwegian (Offentlig utvalg for punktskrift) nwc Newari (old) or Oriya pa Panjabi pi Pali pl Polish pt Portuguese ro Romanian ru Russian sa Sanskrit sat Santali sd Sindhi se Sami (Northern) sk Slovak sl Slovenian sv Swedish sv-1989 Swedish (1989 standard) sv-1996 Swedish (1996 standard) sw Swahili ta Tamil te Telugu tr Turkish uk Ukrainian vi Vietnamese See the ``-t'' command line option, the ``text-table'' configuration file directive, and the ``--with-text-table'' build option for details regarding how to use an alternate text table. 6.1.1. Text Table Format A text table consists of a sequence of directives, one per line, which define how each character is to be represented in braille. UTF-8 character encoding must be used. White-space (blanks, tabs) at the beginning of a line, as well as before and/or after any operand of any directive, is ignored. Lines containing only white-space are ignored. If the first non-white-space character of a line is "#" then that line is a comment and is ignored. 6.1.2. Text Table Directives The following directives are provided: char character dots # comment Use the char directive to specify how a Unicode character is to be represented in braille. Characters defined with this directive can also be entered from a braille keyboard. If several characters have the same braille representation then only one of them should be defined with the char directive - the others should be defined with the glyph directive (which has the same syntax). If more than one character with the same braille representation is defined with the char directive (which is currently allowed for backward compatibility) then the first one is selected. character The Unicode character being defined. It may be: · Any single character other than a backslash or a white- space character. · A backslash-prefixed special character. These are: - \b The backspace character. - \f The formfeed character. - \n The newline character. - \o### The three-digit octal representation of a character. - \r The carriage return character. - \s The space character. - \t The horizontal tab character. - \u#### The four-digit hexadecimal representation of a character. - \U######## The eight-digit hexadecimal representation of a character. - \v The vertical tab character. - \x## The two-digit hexadecimal representation of a character. - \X## ... (the case of the X and of the digits isn't significant) - \# A literal number sign. - \ The Unicode name of a character (use _ for space). - \\ A literal backslash. dots The braille representation of the Unicode character. It is a sequence of one to eight dot numbers. If the dot number sequence is enclosed within parentheses then the dot numbers may be separated from one another by white-space. A dot number is a digit within the range 1-8 as defined by the ``Standard Braille Dot Numbering Convention''. The special dot number 0 is recognized when not enclosed within parentheses, and means no dots; it may not be used in conjunction with any other dot number. Examples: · char a 1 · char b (12) · char c ( 4 1 ) · char \\ 12567 · char \s 0 · char \x20 () · char \ 145 glyph character dots # comment Use the glyph directive to specify how a Unicode character is to be represented in braille. Characters defined with this directive are output-only. They cannot be entered from a braille keyboard. See the char directive for syntax details and for examples. byte byte dots # comment Use the byte directive to specify how a character in the local character set is to be represented in braille. It has been retained for backward compatibility but should not be used. Unicode characters should be defined (via the char directive) so that the text table remains valid regardless of what the local character set is. byte The local character being defined. It may be specified in the same ways as the character operand of the char directive except that the Unicode-specific forms (\u, \U, \<) may not be used. dots The braille representation of the local character. It may be specified in the same ways as the dots operand of the char directive. include file # comment Use the include directive to include the content of a text subtable. It is recursive, which means that any text subtable can itself include yet another text subtable. Care must be taken to ensure that an "include loop" is not created. file The file to be included. It may be either a relative or an absolute path. If relative, it is anchored at the directory containing the including file. 6.2. Attributes Tables Files with names of the form *.atb are attributes tables, and with names of the form *.ati are attributes subtables. They are used when BRLTTY is displaying screen attributes rather than screen content (see the ``DISPMD'' command). Each of the eight braille dots represents one of the eight VGA attribute bits. The following attributes tables are provided: left_right The lefthand column represents the foreground colours: Dot 1 Blue Dot 2 Green Dot 3 Red Dot 7 Bright The righthand column represents the background colours: Dot 4 Blue Dot 5 Green Dot 6 Red Dot 8 Blink A dot is raised when its corresponding attribute bit is on. This is the default attributes table because it's the most intu- itive. One of its problems, though, is that it's difficult to discern the difference between normal (white on black) and reverse (black on white) video. invleft_right The lefthand column represents the foreground colours: Dot 1 Blue Dot 2 Green Dot 3 Red Dot 7 Bright The righthand column represents the background colours: Dot 4 Blue Dot 5 Green Dot 6 Red Dot 8 Blink A background bit being on triggers its corresponding dot, whereas a foreground bit being off triggers its corresponding dot. This unintuitive logic actually makes it easier to read the most commonly used attribute combinations. upper_lower The upper square represents the foreground colours: Dot 1 Red Dot 4 Green Dot 2 Blue Dot 5 Bright The lower square represents the background colours: Dot 3 Red Dot 6 Green Dot 7 Blue Dot 8 Blink A dot is raised when its corresponding attribute bit is on. See the ``-a'' command line option, the ``attributes-table'' configu- ration file directive, and the ``--with-attributes-table'' build option for details regarding how to use an alternate attributes table. 6.2.1. Attributes Table Format An attributes table consists of a sequence of directives, one per line, which define how combinations of VGA attributes are to be represented in braille. UTF-8 character encoding must be used. White-space (blanks, tabs) at the beginning of a line, as well as before and/or after any operand of any directive, is ignored. Lines containing only white-space are ignored. If the first non-white-space character of a line is "#" then that line is a comment and is ignored. 6.2.2. Attributes Table Directives The following directives are provided: dot dot state # comment Use the dot directive to specify what a specific dot represents. dot The dot being defined. It is a single digit within the range 1-8 as defined by the ``Standard Braille Dot Numbering Convention''. state What the dot represents. It may be: =attribute The dot is raised if the named attribute is on. ~attribute The dot is raised if the named attribute is off. The names of the attribute bits are: 0X01 fg-blue 0X02 fg-green 0X04 fg-red 0X08 fg-bright 0X10 bg-blue 0X20 bg-green 0X40 bg-red 0X80 blink Examples: · dot 1 =fg-red · dot 2 ~bg-blue include file # comment Use the include directive to include the content of an attributes subtable. It is recursive, which means that any attributes subtable can itself include yet another attributes subtable. Care must be taken to ensure that an "include loop" is not created. file The file to be included. It may be either a relative or an absolute path. If relative, it is anchored at the directory containing the including file. 6.3. Contraction Tables Files with names of the form *.ctb are contraction tables, and with names of the form *.cti are contraction subtables. They are used by BRLTTY to translate character sequences on the screen into their corresponding contracted braille representations. BRLTTY presents contracted braille if: · A contraction table has been selected. See the ``-c'' command line option and the ``contraction-table'' configuration file directive for details. · The 6-dot braille feature has been activated. See the ``SIXDOTS'' command and the ``Text Style'' preference for details. This feature isn't available if the ``--disable-contracted- braille'' build option was specified. The following contraction tables are provided: Name Language af Afrikaans (contracted) am Amharic (uncontracted) de-basis German (uncontracted) de-kurzschrift German (contracted - 1998 standard) de-kurzschrift-1998 German (contracted - 1998 standard) de-kurzschrift-2015 German (contracted - 2015 standard) de-vollschrift German (basic contractions) en-ueb-g2 English (Unified English Braille, grade 2) en-us-g2 English (US, grade 2) es Spanish (grade 2) fr-abrege French (contracted) fr-integral French (uncontracted) ha Hausa (contracted) id Indonesian (contracted) ja Japanese (uncontracted) ko-g1 Korean (grade 1) ko-g2 Korean (grade 2) ko Korean (uncontracted) lt Lituanian mg Malagasy (contracted) mun Munda (contracted) nl Dutch (contracted) ny Chichewa (contracted) ipa International Phonetic Alphabet pt Portuguese (grade 2) si Sinhalese (uncontracted) sw Swahili (contracted) th Thai (contracted) zh-tw Chinese (Taiwan, uncontracted) zh-tw-ucb Chinese (Taiwan, Unique Chinese Braille) zu Zulu (contracted) See the ``-c'' command line option, and the ``contraction-table'' configuration file directive for details regarding how to use a contraction table. 6.3.1. Contraction Table Format A contraction table consists of a sequence of entries, one per line, which define how character sequences are to be represented in braille. UTF-8 character encoding must be used. White-space (blanks, tabs) at the beginning of a line, as well as before and/or after any operand, is ignored. Lines containing only white-space are ignored. If the first non-white-space character of a line is "#" then that line is a comment and is ignored. The format of a contraction table entry is: directive operand ... [comment] Each directive has a specific number of operands. Any text beyond the last operand of a directive is interpreted as a comment. The order of the entries within a contraction table is, in general, anything that is convenient for its maintainer(s). An entry which defines an entity, e.g. class, must precede all references to that entity. Entries which match character sequences are automatically rearranged from longest to shortest so that longer matches are always preferred. If more than one entry matches the same character sequence then their original table ordering is maintained. Thus, the same sequence may be translated differently under different circumstances. 6.3.2. Contraction Table Operands characters The first operand of a character sequence matching directive is the character sequence to be matched. Each character within the sequence may be: · Any single character other than a backslash or a white-space character. · A backslash-prefixed special character. These are: - \b The backspace character. - \f The formfeed character. - \n The newline character. - \o### The three-digit octal representation of a character. - \r The carriage return character. - \s The space character. - \t The horizontal tab character. - \u#### The four-digit hexadecimal representation of a character. - \U######## The eight-digit hexadecimal representation of a character. - \v The vertical tab character. - \x## The two-digit hexadecimal representation of a character. - \X## ... (the case of the X and of the digits isn't significant) - \# A literal number sign. - \ The Unicode name of a character (use _ for space). - \\ A literal backslash. representation The second operand of those character sequence matching directives which have one is the braille representation of the sequence. Each braille cell is specified as a sequence of one to eight dot numbers. A dot number is a digit within the range 1-8 as defined by the ``Standard Braille Dot Numbering Convention''. The special dot number 0, which may not be used in conjunction with any other dot number, means no dots. 6.3.3. Opcodes An opcode is a keyword which tells the translator how to interpret the operands. The opcodes are grouped here by function. 6.3.3.1. Table Administration These opcodes make it easier to write contraction tables. They have no direct effect on the character translation. include path Include the contents of another file. Nesting can be to any depth. Relative paths are anchored at the directory of the including file. locale locale Define the locale for character interpretation (lowercase, uppercase, numeric, etc.). The locale may be specified as: language[_country][.charset][@modifier] The language component is required and should be a two-letter ISO-639 language code. The country component is optional and should be a two-letter ISO-3166 country code. The charset component is optional and should be a character set name, e.g. ISO-8859-1. C 7-bit ASCII. - No locale. The last locale specification applies to the entire table. If this opcode isn't used then the C locale is assumed. 6.3.3.2. Special Symbol Definition These opcodes define special symbols which must be inserted into the braille text in order to clarify it. capsign dots The symbol which capitalizes a single letter. begcaps dots The symbol which begins a block of capital letters within a word. endcaps dots The symbol which ends a block of capital letters within a word. letsign dots The symbol which marks a letter which isn't part of a word. numsign dots The symbol which marks the beginning of a number. 6.3.3.3. Character Translation These opcodes define the braille representations for character sequences. Each of them defines an entry within the contraction table. These entries may be defined in any order except, as noted below, when they define alternate representations for the same character sequence. Each of these opcodes has a characters operand (which must be specified as a string), and a built-in condition governing its eligibility for use. The text is processed strictly from left to right, character by character, with the most eligible entry for each position being used. If there's more than one eligible entry for a given position, then the one with the longest character string is used. If there's more than one eligible entry for the same character string, then the one defined nearest to the beginning of the table is used (this is the only order dependency). Many of these opcodes have a dots operand which defines the braille representation for its characters operand. It may also be specified as an equals sign (=), in which case it means one of two things. If the entry is for a single character, then it means that the currently selected computer braille representation (see the ``-t'' command line option and the ``text-table'' configuration file directive) for that character is to be used. If it's for a multi-character sequence, then the default representation for each character (see ``always'') within the sequence is to be used. Some special terms are used within the descriptions of these opcodes. word A maximal sequence of one or more consecutive letters. Now, finally, here are the opcode descriptions themselves: literal characters Translate the entire white-space-bounded containing character sequence into computer braille (see the ``-t'' command line option and the ``text-table'' configuration file directive). replace characters characters Replace the first set of characters, no matter where they appear, with the second. The replaced characters aren't reprocessed. always characters dots Translate the characters no matter where they appear. If there's only one character, then, in addition, define the default representation for that character. repeatable characters dots Translate the characters no matter where they appear. Ignore any consecutive repetitions of the same sequence. largesign characters dots Translate the characters no matter where they appear. Remove white-space between consecutive words matched by this opcode. lastlargesign characters dots Translate the characters no matter where they appear. Remove preceding white-space if the previous word was matched by the ``largesign'' opcode. word characters dots Translate the characters if they're a word. joinword characters dots Translate the characters if they're a word. Remove the following white-space if the first character after it is a letter. lowword characters dots Translate the characters if they're a white-space-bounded word. contraction characters Prefix the characters with a letter sign (see ``letsign'') if they're a word. sufword characters dots Translate the characters if they're either a word or at the beginning of a word. prfword characters dots Translate the characters if they're either a word or at the end of a word. begword characters dots Translate the characters if they're at the beginning of a word. begmidword characters dots Translate the characters if they're either at the beginning or in the middle of a word. midword characters dots Translate the characters if they're in the middle of a word. midendword characters dots Translate the characters if they're either in the middle or at the end of a word. endword characters dots Translate the characters if they're at the end of a word. prepunc characters dots Translate the characters if they're part of punctuation at the beginning of a word. postpunc characters dots Translate the characters if they're part of punctuation at the end of a word. begnum characters dots Translate the characters if they're at the beginning of a number. midnum characters dots Translate the characters if they're in the middle of a number. endnum characters dots Translate the characters if they're at the end of a number. 6.3.3.4. Character Classes These opcodes define and use character classes. A character class associates a set of characters with a name. The name then refers to any character within the class. A character may belong to more than one class. The following character classes are automatically predefined based on the selected locale: digit Numeric characters. letter Both uppercase and lowercase alphabetic characters. Some locales have additional letters which are neither uppercase nor lowercase. lowercase Lowercase alphabetic characters. punctuation Printable characters which are neither white-space nor alphanumeric. space White-space characters. In the default locale these are: space, horizontal tab, vertical tab, carriage return, new line, form feed. uppercase Uppercase alphabetic characters. The opcodes which define and use character classes are: class name characters Define a new character class. The characters operand must be specified as a string. A character class may not be used until it's been defined. after class opcode ... The specified opcode is further constrained in that the matched character sequence must be immediately preceded by a character belonging to the specified class. If this opcode is used more than once on the same line then the union of the characters in all the classes is used. before class opcode ... The specified opcode is further constrained in that the matched character sequence must be immediately followed by a character belonging to the specified class. If this opcode is used more than once on the same line then the union of the characters in all the classes is used. 6.4. Key Tables Files with names of the form *.ktb are key tables, and with names of the form *.kti are key subtables. They are used by BRLTTY to bind braille display and keyboard key combinations to BRLTTY commands. The names of braille display key table files begin with brl-xx-", where xx is the two-letter ``driver identification code''. The rest of the name identifies the model(s) for which the key table is used. The names of keyboard table files begin with kbd-. The rest of the name describes the kind of keyboard for which the keyboard table has been designed. The following keyboard tables are provided: braille bindings for braille keyboards desktop bindings for full keyboards keypad bindings for keypad-based navigation laptop bindings for keyboards without a keypad sun_type6 bindings for Sun Type 6 keyboards See the ``-k'' command line option, and the ``keyboard-table'' config- uration file directive for details regarding how to select a keyboard table. 6.4.1. Key Table Directives A key table consists of a sequence of directives, one per line, which define how keys and key combinations are to be interpreted. UTF-8 character encoding must be used. White-space (blanks, tabs) at the beginning of a line, as well as before and/or after any operand, is ignored. Lines containing only white-space are ignored. If the first non-white-space character of a line is a number (#) sign then that line is a comment and is ignored. The precedence for resolving each key press/release event is as follows: 1. A hotkey press or release defined within the current context. See the ``hotkey'' directive for details. 2. A key combination defined within the current context. See the ``bind'' directive for details. 3. A braille keyboard command defined within the current context. See the ``map'' and ``superimpose'' directives for details. 4. A key combination defined within the default context. See the ``bind'' directive for details. The following directives are provided: 6.4.1.1. The Assign Directive Create or update a variable associated with the current include level. The variable is visible to the current and to lower include levels, but not to higher include levels. assign variable [value] variable The name of the variable. If the variable doesn't already exist at the current include level then it is created. value The value which is to be assigned to the variable. If it's not supplied then a zero-length (null) value is assigned. The escape sequence \{variable} is substituted with the value of the variable named within the braces. The variable must have been defined at the current or at a higher include level. Examples: · assign nullValue · assign ReturnKey Key1 · bind \{ReturnKey} RETURN 6.4.1.2. The Bind Directive Define which BRLTTY command is executed when a particular combination of one or more keys is pressed. The binding is defined within the current context. bind keys command keys The key combination which is to be bound. It's a sequence of one or more key names separated by plus (+) signs. The final (or only) key name may be optionally prefixed with an exclamation (!) point. The keys may be pressed in any order, with the exception that if the final key name is prefixed with an exclamation point then it must be pressed last. The exclamation point prefix means that the command is executed as soon as that key is pressed. If not used, the command is executed as soon as any of the keys is released. command The name of a BRLTTY command. One or more modifiers may be optionally appended to the command name by using a plus (+) sign as the separator. · For commands which enable/disable a feature: · If the modifier +on is specified then the feature is enabled. · If the modifier +off is specified then the feature is disabled. · If neither +on nor +off is specified then the state of the feature is toggled on/off. · For commands which move the braille window: · If the modifier +route is specified then, if necessary, the cursor is automatically routed so that it's always visible on the braille display. · For commands which move the braille window to a specific line on the screen: · If the modifier +toleft is specified then the braille window is also moved to the beginning of that line. · If the modifier +scaled is specified then the set of keys bound to the command is interpreted as though it were a scroll bar. If it isn't, then there's a one-to-one correspondence between keys and lines. · For commands which require an offset: · The modifier +offset, where offset is a non-negative integer, may be specified. If it isn't supplied then +0 is assumed. Examples: · bind Key1 CSRTRK · bind Key1+Key2 CSRTRK+off · bind Key1+Key3 CSRTRK+on · bind Key4 TOP · bind Key5 TOP+route · bind VerticalSensor GOTOLINE+toleft+scaled · bind Key6 CONTEXT+1 6.4.1.3. The Context Directive Define alternate ways to interpret certain key events and/or combinations. A context contains definitions created by the ``bind'', ``hotkey'', ``ignore'', ``map'', and ``superimpose'' directives. context name [title] name Which context subsequent definitions are to be created within. These special contexts are predefined: default The default context. If a key combination hasn't been defined within the current context then its definition within the default context is used. This only applies to definitions created by the ``bind'' directive. menu This context is used when within BRLTTY's preferences menu. title A person-readable description of the context. It may contain spaces, and standard capitalization conventions should be used. This operand is optional. If supplied when selecting a context which already has a title then the two must match. Special contexts already have internally-assigned titles. A context is created the first time it's selected. It may be reselected any number of times thereafter. All subsequent definitions until either the next ``context'' directive or the end of the current include level are created within the selected context. The initial context of the top-level key table is default. The initial context of an included key subtable is the context which was selected when it was included. Context changes within included key subtables don't affect the context of the including key table or subtable. If a context has a title then it is persistent. When a key event causes a persistent context to be activated, that context remains current until a subsequent key event causes a different persistent context to be activated. If a context doesn't have a title then it is temporary. When a key event causes a temporary context to be activated, that context is only used to interpret the very next key event. Examples: · context menu · context braille Braille Input · context DESCCHAR 6.4.1.4. The Hide Directive Specify whether or not certain definitions (see the ``bind'', ``hotkey'', ``map'', and ``superimpose'' directives) and notes (see the ``note'' directive) are included within the key table's help text. hide state state One of these keywords: on They're excluded. off They're included. The specified state applies to all subsequent definitions and notes until either the next hide directive or the end of the current include level. The initial state of the top-level key table is off. The initial state of an included key subtable is the state which was selected when it was included. State changes within included key subtables don't affect the state of the including key table or subtable. Examples: · hide on 6.4.1.5. The Hotkey Directive Bind the press and release events of a specific key to two separate BRLTTY commands. The bindings are defined within the current context. hotkey key press release key The name of the key which is to be bound. press The name of the BRLTTY command which is to be executed whenever the key is pressed. release The name of the BRLTTY command which is to be executed whenever the key is released. Modifiers may be appended to the command names. See the command operand of the ``bind'' directive for details. Specify NOOP if no command is to be executed. Specifying NOOP for both commands effectively disables the key. Examples: · hotkey Key1 CSRVIS+off CSRVIS+on · hotkey Key2 NOOP NOOP 6.4.1.6. The IfKey Directive Conditionally process a key table directive only if the device has a particular key. ifkey key directive key The name of the key whose availability is to be tested. directive The key table directive which is to be conditionally processed. Examples: · ifkey Key1 ifkey Key2 bind Key1+Key2 HOME 6.4.1.7. The Include Directive Process the directives within a key subtable. It's recursive, which means that any key subtable can itself include yet another key subtable. Care must be taken to ensure that an "include loop" is not created. include file file The key subtable which is to be included. It may be either a relative or an absolute path. If relative, it's anchored at the directory containing the including key table or subtable. Examples: · include common.kti · include /path/to/my/keys.kti 6.4.1.8. The Ignore Directive Ignore a specific key while within the current context. ignore key key The name of the key which is to be ignored. Examples: · ignore Key1 6.4.1.9. The Map Directive Map a key to a braille keyboard function. The mapping is defined within the current context. map key function key The name of the key which is to be mapped. More than one key may be mapped to the same braille keyboard function. function The name of the braille keyboard function. It may be one of the following keywords: DOT1 The upper-left standard braille dot. DOT2 The middle-left standard braille dot. DOT3 The lower-left standard braille dot. DOT4 The upper-right standard braille dot. DOT5 The middle-right standard braille dot. DOT6 The lower-right standard braille dot. DOT7 The lower-left computer braille dot. DOT8 The lower-right computer braille dot. SPACE The space bar. SHIFT The shift key. UPPER If a lowercase letter is being entered then translate it to its uppercase equivalent. CONTROL The control key. META The left alt key. If a key combination consists only of keys which have been mapped to braille keyboard functions, and if those functions when combined form a valid braille keyboard command, then that command is executed as soon as any of the keys is released. A valid braille keyboard command must include either any combination of dot keys or the space bar (but not both). If at least one dot key is included then the braille keyboard functions specified by the ``superimpose'' directives within the same context are also implicitly included. Examples: · map Key1 DOT1 6.4.1.10. The Note Directive Add a person-readable explanation to the key table's help text. Notes are commonly used, for example, to describe the placement, sizes, and shapes of the keys on the device. note text text The explanation which is to be added. It may contain spaces, and should be grammatically correct. Each note specifies exactly one line of explanatory text. Leading space is ignored so indentation cannot be specified. There's no limit to the number of notes which may be specified. All of them are gathered together and presented in a single block at the start of the key table's help text. Examples: · note Key1 is the round key at the far left on the front surface. 6.4.1.11. The Superimpose Directive Implicitly include a braille keyboard function whenever a braille keyboard command consisting of at least one dot is executed. The implicit inclusion is defined within the current context. Any number of them may be specified. superimpose function function The name of the braille keyboard function. See the function operand of the ``map'' directive for details. Examples: · superimpose DOT7 6.4.1.12. The Title Directive Provide a person-readable summary of the key table's purpose. title text text A one-line summary of what the key table is used for. It may contain spaces, and standard capitalization conventions should be used. The title of the key table may be specified only once. Examples: · title Bindings for Keypad-based Navigation 6.4.2. Keyboard Properties The default is that all keyboards are monitored. A subset of the keyboards may be selected by specifying one or more of the following properties (see the ``-K'' command line option, and the ``keyboard- properties'' configuration file directive): type The bus type, specified as one of the following keywords: any, ps2, usb, bluetooth. vendor The vendor identifier, specified as a 16-bit unsigned integer. product The product identifier, specified as a 16-bit unsigned integer. The vendor and product identifiers may be specified in decimal (no prefix), octal (prefixed by 0), or hexadecimal (prefixed by 0x). Specifying 0 means match any value (as if the property weren't specified). 7. Advanced Topics 7.1. Installing Multiple Versions It's easy to have more than one version of BRLTTY installed on the same system at the same time. This capability allows you to test a new version before removing the old one. The ``--with-execute-root'' build option allows you to install the complete ``installed file hierarchy'' anywhere you want such that it's entirely self-contained. Remembering that it's best to keep all of BRLTTY's components within the root file system, you can build it like this: ./configure --with-execute-root=/brltty-3.1 make install You can then run it like this: /brltty-3.1/bin/brltty When version 3.2 is released, just install it in a different location and run the new executable from there. ./configure --with-execute-root=/brltty-3.2 make install /brltty-3.2/bin/brltty So far, this paradigm is somewhat awkward for at least two reasons. One is that these long path names are too hard to type, and the other is that you don't want to fiddle with your system's boot sequence each time you want to switch to a different version of BRLTTY. These problems are easily solved by adding a symbolic link for the executable. ln -s /brltty-3.1/bin/brltty /bin/brltty When it's time to switch to the newer version, just repoint the sym- bolic link. ln -s /brltty-3.2/bin/brltty /bin/brltty If you'd like to get really fancy, then introduce another level of indirection in order to make all of BRLTTY's files for any given version look like they're in all of the standard places. First, create a symbolic link through a common repointable location from each of BRLTTY's standard locations. ln -s /brltty/bin/brltty /bin/brltty ln -s /brltty/etc/brltty /etc/brltty ln -s /brltty/lib/brltty /lib/brltty Then all you need to do is to point /brltty to the desired version. ln -s /brltty-3.1 /brltty 7.2. Installation/Rescue Root Disks for Linux BRLTTY can run as a stand-alone executable. Everything it needs to know can be explicitly configured at build-time (see ``Build Options''). If the data directory (see the ``--with-data-directory'' and ``--with-execute-root'' build options) doesn't exist, then BRLTTY looks in /etc for the files it needs. Even if any of these files don't exist at all, BRLTTY still works! If, for some reason, you ever create the data directory (usually /etc/brltty) by hand, it's important to set its permissions so that only root can create files within it. chmod 755 /etc/brltty The screen content inspection device (usually /dev/vcsa) is required. It should already exist unless your Linux distribution is quite old. If necessary, you can create it with: mknod /dev/vcsa c 7 128 chmod 660 /dev/vcsa chown root.tty /dev/vcsa One problem often encountered when trying to use BRLTTY in an uncertain environment like a root disk or an incomplete system is that it might not find the shared libraries (or parts thereof) which it needs. Root disks often use subset and/or outdated versions of the libraries which may be inadequate. The solution is to configure BRLTTY with the ``--enable-standalone-programs'' build option. This removes all dependencies on shared libraries, but, unfortunately, also creates a larger executable. There are a number of build options which can be used to selectively remove unneeded features from BRLTTY in order to somewhat mitigate this problem (see section ``Build Features''). The executable is stripped during the ``make install''. This significantly reduces its size by removing its symbol table. You'll get a much smaller executable, therefore, if you complete the full build procedure, and then copy it from its installed location. If, however, you copy it from the build directory, it'll be way too big. Don't forget to strip it. strip brltty 7.3. Future Enhancements Apart from fixing bugs and supporting more types of braille displays, we hope, time permitting, to work on the following: Better Attribute Handling · Attribute tracking. · Mixed text and attribute mode. Scroll Tracking Locking the braille window to one line as it scrolls on the screen. Better Speech Support · Mixed braille and speech for faster reading of text. · Better speech navigation. · More speech synthesizers. Screen Subregions Ignore cursor motion outside the region, and set soft navigational boundaries at the edges of the region. See the file TODO for a more complete list. 7.4. Known Bugs At the time of writing (December 2001), the following problems are known: Cursor routing is implemented as a looping sub-process which runs at reduced priority to avoid using too much cpu time. Different system loads require different settings of its parameters. The defaults work very well in a typical Unix editor on a fairly lightly loaded system, but very poorly in some other situations, e.g. over a slow serial link to a remote host. A. Supported Braille Displays BRLTTY supports the following braille displays: Name Models ______________________________________________________________ Albatross 46/80 Alva ABT (3nn) Delphi (4nn) Satellite (5nn) Braille System 40 Braille Controller 640/680 Easy Link 12 B2G Baum BrailleConnect 12/24/32/40/64/80 Brailliant 24/32/40/64/80 Conny 12 DM80 Plus EcoVario 24/32/40/64/80 Inka Orbit 20 PocketVario 24 Pronto! V3 18/40 Pronto! V4 18/40 RBT 40/80 Refreshabraille 18 SuperVario 32/40/64/80 Vario 40/80 VarioConnect 12/24/32/40/64/80 VarioPro 40/64/80 VarioUltra 20/32/40 BrailComm III BrailleLite 18/40/M20/M40 BrailleMemo Pocket (16) Smart (16) 32 40 BrailleNote 18/32 Apex Braudi BrlAPI Cebra 20/40/60/80/100/120/140 CombiBraille 25/45/85 EcoBraille 20/40/80 EuroBraille AzerBraille Clio Esys Iris NoteBraille Scriba FreedomScientific Focus 1 44/70/84 Focus 2 40/80 Focus Blue 14/40/80 PAC Mate 20/40 HandyTech Modular 20/40/80 Modular Evolution 64/88 Modular Connect 88 Active Braille Active Star 40 Actilino Activator Basic Braille 16/20/32/40/48/64/80 Braillino Braille Wave Easy Braille Braille Star 40/80 Connect Braille 40 Bookworm Hedo ProfiLine MobilLine HIMS Braille Sense SyncBraille Braille Edge Smart Beetle HumanWare Brailliant BI 14/32/40 Brailliant B 80 BrailleNote Touch Inceptor BrailleMe Iris Libbraille LogText 32 MDV MB208 MB248 MB408L MB408L+ Lilli Blu Metec BD-40 MiniBraille 20 MultiBraille MB125CR/MB145CR/MB185CR NinePoint 8 Papenmeier Compact 486 Compact/Tiny IB 80 CR Soft 2D Lite (plus) 2D Screen Soft EL 80 EL 2D 40/66/80 EL 40/66/70/80 S EL 40/60/80 C EL 2D 80 S EL 40 P EL 80 II Elba 20/32 Trio 40/Elba20/Elba32 Live 20/40 Pegasus 20/27/40/80 Seika 3/4/5 (40) 80 Mini (16) TechniBraille TSI Navigator 20/40/80 PowerBraille 40/65/80 TTY terminfo VideoBraille 40 Virtual TCP/Unix, client/server VisioBraille 20/40 Voyager 44/70 Part232 (serial adapter) BraillePen/EasyLink XWindow X11 Windows B. Supported Speech Synthesizers BRLTTY supports the following speech synthesizers: Name Models _____________________________________________________________ Alva Delphi (4nn) Android text to speech engine BrailleLite CombiBraille eSpeak text to speech engine eSpeak-NG text to speech engine ExternalSpeech runs /usr/local/bin/externalspeech Festival text to speech engine FestivalLite text to speech engine GenericSay pipes to /usr/local/bin/say Mikropuhe text to speech engine Swift text to speech engine Theta text to speech engine ViaVoice text to speech engine C. Driver Identification Codes Code Name ____________________________________________________ al Alva an Android at Albatross ba BrlAPI bc BrailComm bd Braudi bg B2G bl BrailleLite bm Baum (Native, HT, PB1, PB2) bn BrailleNote cb CombiBraille ec EcoBraille en eSpeak-NG es eSpeak eu EuroBraille fl FestivalLite fs FreedomScientific fv Festival gs GenericSay hd Hedo hm HIMS ht HandyTech hw HumanWare ic Inceptor ir Iris lb Libbraille lt LogText mb MultiBraille md MDV mm BrailleMemo mn MiniBraille mp Mikropuhe mt Metec no no driver np NinePoint pg Pegasus pm Papenmeier sd SpeechDispatcher sk Seika sw Swift th Theta tn TechniBraille ts Telesensory Systems Inc. tt TTY vd VideoBraille vo Voyager vr Virtual vs VisioBraille vv ViaVoice xs ExternalSpeech xw XWindow D. Supported Screen Drivers BRLTTY supports the following screen drivers: as AT-SPI hd This driver provides direct access to the Hurd console screen. It's only selectable, and is the default, on Hurd systems. lx This driver provides direct access to the Linux console screen. It's only selectable, and is the default, on Linux systems. sc This driver provides access to the screen program. It's selectable on all systems, and is the default if no native screen driver is available. The patch for screen which we provide (see the Patches subdirectory) must be applied. Use of this driver, due to the fact that screen must be concurrently running, makes BRLTTY effectively useful only after the user has logged in. wn This driver provides direct access to the Windows console screen. It's only selectable, and is the default, on Windows/Cygwin systems. E. Operand Syntax E.1. Driver Specification A braille display or speech synthesizer driver must be specified via its two-letter ``driver identification code''. A comma-delimited list of drivers may be specified. If this is done then autodetection is performed using each listed driver in sequence. You may need to experiment in order to determine the most reliable order since some drivers autodetect better than others. If the single word auto is specified then autodetection is performed using only those drivers which are known to be reliable for this purpose. E.2. Braille Device Specification The general form of a braille device specification (see the ``-d'' command line option, the ``braille-device'' configuration file directive, and the ``--with-braille-device'' build option) is qualifier:data. For backward compatibility with earlier releases, if the qualifier is omitted then serial: is assumed. The following device types are supported: Bluetooth For a bluetooth device, specify bluetooth:address. The address must be six two-digit hexadecimal numbers separated by colons, e.g. 01:23:45:67:89:AB. Serial For a serial device, specify serial:/path/to/device. The serial: qualifier is optional (for backward compatibility). If a relative path is given then it's anchored at /dev (the usual location where devices are defined on a Unix-like system). The following device specifications all refer to the first serial device on Linux: · serial:/dev/ttyS0 · serial:ttyS0 · /dev/ttyS0 · ttyS0 USB For a USB device, specify usb:. BRLTTY will search for the first USB device which matches the braille display driver being used. If this is inadequate, e.g. if you have more than one USB braille display which requires the same driver, then you can refine the device specification by appending the serial number of the display to it, e.g. usb:12345. N.B.: The "identification by serial number" feature doesn't work for some models because some manufacturers either don't set the USB serial number descriptor at all or do set it but not to a unique value. A comma-delimited list of braille devices may be specified. If this is done then autodetection is performed on each listed device in sequence. This feature is particularly useful if you have a braille display with more than one interface, e.g. both a serial and a USB port. In this case it's usually better to list the USB port first, e.g. usb:,serial:/dev/ttyS0, since the former tends to autodetect more reliably than the latter. E.3. PCM Device Specification In most cases the PCM device is the full path to an appropriate system device. Exceptions are: ALSA The name of and arguments for the physical or logical device, i.e. name[:argument,...]. The default PCM device is: Platform Device _______________________________________________________ FreeBSD /dev/dsp Linux/ALSA hw:0,0 Linux/OSS /dev/dsp NetBSD /dev/audio OpenBSD /dev/audio Qnx preferred PCM output device Solaris /dev/audio E.4. MIDI Device Specification In most cases the MIDI device is the full path to an appropriate system device. Exceptions are: ALSA The client and port separated by a colon, i.e. client:port. Each may be specified either as a number or as a case-sensitive substring of its name. The default MIDI device is: Platform Device ____________________________________________________________ Linux/ALSA the first available MIDI output port Linux/OSS /dev/sequencer F. Standard Braille Dot Numbering Convention A standard braille cell consists of six dots arranged in three rows and two columns. Each dot can be specifically identified by its number as follows: 1 Top-left (row 1, column 1). 2 Middle-left (row 2, column 1). 3 Bottom-left (row 3, column 1). 4 Top-right (row 1, column 2). 5 Middle-right (row 2, column 2). 6 Bottom-right (row 3, column 2). Computer braille has introduced a fourth row at the bottom. 7 Below-left (row 4, column 1). 8 Below-right (row 4, column 2). Perhaps a picture will make this numbering convention easier to understand. 1 o o 4 2 o o 5 3 o o 6 7 o o 8 G. North American Braille Computer Code Num Hex Dots Description +-----------------------------------------------------------------+ | 0 00 [7 4 8] NUL (null) | | 1 01 [7 1 8] SOH (start of header) | | 2 02 [7 21 8] STX (start of text) | | 3 03 [7 14 8] ETX (end of text) | | 4 04 [7 145 8] EOT (end of transmission) | | 5 05 [7 1 5 8] ENQ (enquiry) | | 6 06 [7 214 8] ACK (acknowledge) | | 7 07 [7 2145 8] BEL (bell) | | 8 08 [7 21 5 8] BS (back space) | | 9 09 [7 2 4 8] HT (horizontal tab) | | 10 0A [7 2 45 8] LF (line feed) | | 11 0B [73 1 8] VT (vertical tab) | | 12 0C [7321 8] FF (form feed) | | 13 0D [73 14 8] CR (carriage return) | | 14 0E [73 145 8] SO (shift out) | | 15 0F [73 1 5 8] SI (shift in) | | 16 10 [73214 8] DLE (data link escape) | | 17 11 [732145 8] DC1 (direct control 1) | | 18 12 [7321 5 8] DC2 (direct control 2) | | 19 13 [732 4 8] DC3 (direct control 3) | | 20 14 [732 45 8] DC4 (direct control 4) | | 21 15 [73 1 68] NAK (negative acknowledge) | | 22 16 [7321 68] SYN (synchronize) | | 23 17 [7 2 4568] ETB (end of text block) | | 24 18 [73 14 68] CAN (cancel) | | 25 19 [73 14568] EM (end of medium) | | 26 1A [73 1 568] SUB (substitute) | | 27 1B [7 2 4 68] ESC (escape) | | 28 1C [7 21 568] FS (file separator) | | 29 1D [7 214568] GS (group separator) | | 30 1E [7 45 8] RS (record separator) | | 31 1F [7 4568] US (unit separator) | | 32 20 [ ] space | | 33 21 [ 32 4 6 ] exclamation point | | 34 22 [ 5 ] quotation mark | | 35 23 [ 3 456 ] number sign | | 36 24 [ 214 6 ] dollar sign | | 37 25 [ 14 6 ] percent sign | | 38 26 [ 3214 6 ] ampersand | | 39 27 [ 3 ] acute accent | | 40 28 [ 321 56 ] left parenthesis | | 4 291 [ 32 456 ) right parenthesis | | 42 2A [ 1 6 ] asterisk | | 43 2B [ 3 4 6 ] plus sign | | 44 2C [ 6 ] comma | | 45 2D [ 3 6 ] minus sign | | 46 2E [ 4 6 ] period | | 47 2F [ 3 4 ] forward slash | | 48 30 [ 3 56 ] zero | | 49 31 [ 2 ] one | | 50 32 [ 32 ] two | | 51 33 [ 2 5 ] three | | 52 34 [ 2 56 ] four | | 53 35 [ 2 6 ] five | | 54 36 [ 32 5 ] six | | 55 37 [ 32 56 ] seven | | 56 38 [ 32 6 ] eight | | 57 39 [ 3 5 ] nine | | 58 3A [ 1 56 ] colon | | 59 3B [ 56 ] semicolon | | 60 3C [ 21 6 ] less-than sign | | 61 3D [ 321456 ] equals sign | | 62 3E [ 3 45 ] greater-than sign | | 63 3F [ 1456 ] question mark | | 64 40 [7 4 ] commercial at | | 65 41 [7 1 ] capital a | | 66 42 [7 21 ] capital b | | 67 43 [7 14 ] capital c | | 68 44 [7 145 ] capital d | | 69 45 [7 1 5 ] capital e | | 70 46 [7 214 ] capital f | | 71 47 [7 2145 ] capital g | | 72 48 [7 21 5 ] capital h | | 73 49 [7 2 4 ] capital i | | 74 4A [7 2 45 ] capital j | | 75 4B [73 1 ] capital k | | 76 4C [7321 ] capital l | | 77 4D [73 14 ] capital m | | 78 4E [73 145 ] capital n | | 79 4F [73 1 5 ] capital o | | 80 50 [73214 ] capital p | | 81 51 [732145 ] capital q | | 82 52 [7321 5 ] capital r | | 83 53 [732 4 ] capital s | | 84 54 [732 45 ] capital t | | 85 55 [73 1 6 ] capital u | | 86 56 [7321 6 ] capital v | | 87 57 [7 2 456 ] capital w | | 88 58 [73 14 6 ] capital x | | 89 59 [73 1456 ] capital y | | 90 5A [73 1 56 ] capital z | | 91 5B [7 2 4 6 ] left bracket | | 92 5C [7 21 56 ] backward slash | | 93 5D [7 21456 ] right bracket | | 94 5E [7 45 ] circumflex accent | | 95 5F [ 456 ] underscore | | 96 60 [ 4 ] grave accent | | 97 61 [ 1 ] small a | | 98 62 [ 21 ] small b | | 99 63 [ 14 ] small c | | 100 64 [ 145 ] small d | | 101 65 [ 1 5 ] small e | | 102 66 [ 214 ] small f | | 103 67 [ 2145 ] small g | | 104 68 [ 21 5 ] small h | | 105 69 [ 2 4 ] small i | | 106 6A [ 2 45 ] small j | | 107 6B [ 3 1 ] small k | | 108 6C [ 321 ] small l | | 109 6D [ 3 14 ] small m | | 110 6E [ 3 145 ] small n | | 111 6F [ 3 1 5 ] small o | | 112 70 [ 3214 ] small p | | 113 71 [ 32145 ] small q | | 114 72 [ 321 5 ] small r | | 115 73 [ 32 4 ] small s | | 116 74 [ 32 45 ] small t | | 117 75 [ 3 1 6 ] small u | | 118 76 [ 321 6 ] small v | | 119 77 [ 2 456 ] small w | | 120 78 [ 3 14 6 ] small x | | 121 79 [ 3 1456 ] small y | | 122 7A [ 3 1 56 ] small z | | 123 7B [ 2 4 6 ] left brace | | 124 7C [ 21 56 ] vertical bar | | 125 7D [ 21456 ] right brace | | 126 7E [ 45 ] tilde accent | | 127 7F [7 456 ] DEL (delete) | | 128 80 [ 4 8] | | 129 81 [ 1 8] | | 130 82 [ 21 8] BPH (break permitted here) | | 131 83 [ 14 8] NBH (no break here) | | 132 84 [ 145 8] | | 133 85 [ 1 5 8] NL (next line) | | 134 86 [ 214 8] SSA (start of selected area) | | 135 87 [ 2145 8] ESA (end of selected area) | | 136 88 [ 21 5 8] CTS (character tabulation set) | | 137 89 [ 2 4 8] CTJ (character tabulation justification) | | 138 8A [ 2 45 8] LTS (line tabulation set) | | 139 8B [ 3 1 8] PLD (partial line down) | | 140 8C [ 321 8] PLU (partial line up) | | 141 8D [ 3 14 8] RLF (reverse line feed) | | 142 8E [ 3 145 8] SS2 (single shift two) | | 143 8F [ 3 1 5 8] SS3 (single shift three) | | 144 90 [ 3214 8] DCS (device control string) | | 145 91 [ 32145 8] PU1 (private use one) | | 146 92 [ 321 5 8] PU2 (private use two) | | 147 93 [ 32 4 8] STS (set transmit state) | | 148 94 [ 32 45 8] CC (cancel character) | | 149 95 [ 3 1 68] MW (message waiting) | | 150 96 [ 321 68] SGA (start of guarded area) | | 151 97 [ 2 4568] EGA (end of guarded area) | | 152 98 [ 3 14 68] SS (start of string) | | 153 99 [ 3 14568] | | 154 9A [ 3 1 568] SCI (single character introducer) | | 155 9B [ 2 4 68] CSI (control sequence introducer) | | 156 9C [ 21 568] ST (string terminator) | | 157 9D [ 214568] OSC (operating system command) | | 158 9E [ 45 8] PM (privacy message) | | 159 9F [ 4568] APC (application program command) | | 160 A0 [7 8] no-break space | | 161 A1 [732 4 6 ] inverted exclamation mark | | 162 A2 [7 214 6 ] cent sign | | 163 A3 [73 456 ] pound sign | | 164 A4 [7 14 6 ] currency sign | | 165 A5 [73214 6 ] yen sign | | 166 A6 [7 1 56 ] broken bar | | 167 A7 [73 5 ] section sign | | 168 A8 [7 5 ] diaeresis | | 169 A9 [732 56 ] copyright sign | | 170 AA [ 8] feminine ordinal indicator | | 171 AB [7 21 6 ] left-pointing double angle quotation mark | | 172 AC [7 2 56 ] not sign | | 173 AD [73 6 ] soft hyphen | | 174 AE [732 6 ] registered sign | | 175 AF [7 2 6 ] macron | | 176 B0 [73 56 ] degree sign | | 177 B1 [73 4 6 ] plus-minus sign | | 178 B2 [732 ] superscript two | | 179 B3 [7 2 5 ] superscript three | | 180 B4 [73 ] acute accent | | 181 B5 [7 56 ] micro sign | | 182 B6 [732 5 ] pilcrow sign | | 183 B7 [7 4 6 ] middle dot | | 184 B8 [7 6 ] cedilla | | 185 B9 [7 2 ] superscript one | | 186 BA [7 ] masculine ordinal indicator | | 187 BB [73 45 ] right-pointing double angle quotation mark | | 188 BC [7321 56 ] vulgar fraction one quarter | | 189 BD [7321456 ] vulgar fraction one half | | 190 BE [732 456 ] vulgar fraction three quarters | | 191 BF [7 1456 ] inverted question mark | | 192 C0 [732 5 8] capital a grave | | 193 C1 [7 1 68] capital a acute | | 194 C2 [7 2 8] capital a circumflex | | 195 C3 [7 5 8] capital a tilde | | 196 C4 [73214 68] capital a diaeresis | | 197 C5 [73 45 8] capital a ring above | | 198 C6 [73 8] capital ae | | 199 C7 [73 4 68] capital c cedilla | | 200 C8 [732 568] capital e grave | | 201 C9 [7 21 68] capital e acute | | 202 CA [732 8] capital e circumflex | | 203 CB [73214568] capital e diaeresis | | 204 CC [732 68] capital i grave | | 205 CD [7 14 68] capital i acute | | 206 CE [7 2 5 8] capital i circumflex | | 207 CF [7321 568] capital i diaeresis | | 208 D0 [7 68] capital eth | | 209 D1 [7 4 68] capital n tilde | | 210 D2 [73 5 8] capital o grave | | 211 D3 [7 14568] capital o acute | | 212 D4 [7 2 568] capital o circumflex | | 213 D5 [7 568] capital o tilde | | 214 D6 [732 4 68] capital o diaeresis | | 215 D7 [7 1 6 ] multiplication sign | | 216 D8 [73 4 8] capital o stroke | | 217 D9 [73 568] capital u grave | | 218 DA [7 1 568] capital u acute | | 219 DB [7 2 68] capital u circumflex | | 220 DC [732 4568] capital u diaeresis | | 221 DD [7 214 68] capital y acute | | 222 DE [73 68] capital thorn | | 223 DF [73 4568] small sharp s | | 224 E0 [ 32 5 8] small a grave | | 225 E1 [ 1 68] small a acute | | 226 E2 [ 2 8] small a circumflex | | 227 E3 [ 5 8] small a tilde | | 228 E4 [ 3214 68] small a diaeresis | | 229 E5 [ 3 45 8] small a ring above | | 230 E6 [ 3 8] small ae | | 231 E7 [ 3 4 68] small c cedilla | | 232 E8 [ 32 568] small e grave | | 233 E9 [ 21 68] small e acute | | 234 EA [ 32 8] small e circumflex | | 235 EB [ 3214568] small e diaeresis | | 236 EC [ 32 68] small i grave | | 237 ED [ 14 68] small i acute | | 238 EE [ 2 5 8] small i circumflex | | 239 EF [ 321 568] small i diaeresis | | 240 F0 [ 68] small eth | | 241 F1 [ 4 68] small n tilde | | 242 F2 [ 3 5 8] small o grave | | 243 F3 [ 14568] small o acute | | 244 F4 [ 2 568] small o circumflex | | 245 F5 [ 568] small o tilde | | 246 F6 [ 32 4 68] small o diaeresis | | 247 F7 [73 4 ] division sign | | 248 F8 [ 3 4 8] small o stroke | | 249 F9 [ 3 568] small u grave | | 250 FA [ 1 568] small u acute | | 251 FB [ 2 68] small u circumflex | | 252 FC [ 32 4568] small u diaeresis | | 253 FD [ 214 68] small y acute | | 254 FE [ 3 68] small thorn | | 255 FF [ 3 4568] small y diaeresis | +-----------------------------------------------------------------+ H. MIDI Instrument Table _____________________________________________________________ Piano 0 Acoustic Grand Piano 1 Bright Acoustic Piano 2 Electric Grand Piano 3 Honkytonk Piano 4 Electric Piano 1 5 Electric Piano 2 6 Harpsichord 7 Clavi _____________________________________________________________ Chromatic Percussion 8 Celesta 9 Glockenspiel 10 Music Box 11 Vibraphone 12 Marimba 13 Xylophone 14 Tubular Bells 15 Dulcimer _____________________________________________________________ Organ 16 Drawbar Organ 17 Percussive Organ 18 Rock Organ 19 Church Organ 20 Reed Organ 21 Accordion 22 Harmonica 23 Tango Accordion _____________________________________________________________ Guitar 24 Nylon Acoustic Guitar 25 Steel Acoustic Guitar 26 Jazz Electric Guitar 27 Clean Electric Guitar 28 Muted Electric Guitar 29 Overdriven Guitar 30 Distortion Guitar 31 Guitar Harmonics _____________________________________________________________ Bass 32 Acoustic Bass 33 Finger Electric Bass 34 Pick Electric Bass 35 Fretless Bass 36 Slap Bass 1 37 Slap Bass 2 38 Synth Bass 1 39 Synth Bass 2 _____________________________________________________________ Strings 40 Violin 41 Viola 42 Cello 43 Contrabass 44 Tremolo Strings 45 Pizzicato Strings 46 Orchestral Harp 47 Timpani _____________________________________________________________ Ensemble 48 String Ensemble 1 49 String Ensemble 2 50 Synth Strings 1 51 Synth Strings 2 52 Choir Aahs 53 Voice Oohs 54 Synth Voice 55 Orchestra Hit _____________________________________________________________ Brass 56 Trumpet 57 Trombone 58 Tuba 59 Muted Trumpet 60 French Horn 61 Brass Section 62 Synth Brass 1 63 Synth Brass 2 _____________________________________________________________ Reed 64 Soprano Saxophone 65 Alto Saxophone 66 Tenor Saxophone 67 Baritone Saxophone 68 Oboe 69 English Horn 70 Bassoon 71 Clarinet _____________________________________________________________ Pipe 72 Piccolo 73 Flute 74 Recorder 75 Pan Flute 76 Blown Bottle 77 Shakuhachi 78 Whistle 79 Ocarina _____________________________________________________________ Synth Lead 80 Lead 1 (square) 81 Lead 2 (sawtooth) 82 Lead 3 (calliope) 83 Lead 4 (chiff) 84 Lead 5 (charang) 85 Lead 6 (voice) 86 Lead 7 (fifths) 87 Lead 8 (bass + lead) _____________________________________________________________ Synth Pad 88 Pad 1 (new age) 89 Pad 2 (warm) 90 Pad 3 (polysynth) 91 Pad 4 (choir) 92 Pad 5 (bowed) 93 Pad 6 (metallic) 94 Pad 7 (halo) 95 Pad 8 (sweep) _____________________________________________________________ Synth FM 96 FX 1 (rain) 97 FX 2 (soundtrack) 98 FX 3 (crystal) 99 FX 4 (atmosphere) 100 FX 5 (brightness) 101 FX 6 (goblins) 102 FX 7 (echoes) 103 FX 8 (science-fiction) _____________________________________________________________ Ethnic 104 Sitar 105 Banjo 106 Shamisen 107 Koto 108 Kalimba 109 Bag Pipe 110 Fiddle 111 Shanai _____________________________________________________________ Percussive 112 Tinkle Bell 113 Agogo 114 Steel Drum 115 Wooden Block 116 Taiko Drum 117 Melodic Tom 118 Synth Drum 119 Reverse Cymbal _____________________________________________________________ Sound Effects 120 Guitar Fret Noise 121 Breath Noise 122 Seashore 123 Bird Tweet 124 Telephone Ring 125 Helicopter 126 Applause 127 Gunshot