BDF2PSF(1) Console-setup User's Manual BDF2PSF(1) NAME bdf2psf - convert a BDF font to PSF format for the Linux console SYNOPSIS bdf2psf [--fb] [--log logfile] bdf{+bdf} equivalence{+equivalence} sym- bols{+[:]symbols} size psf [sfm] DESCRIPTION The program bdf2psf translates BDF fonts to PSF format. It accepts fonts with arbitrary size of the font matrix. If the width of the glyph matrix of the source font is 7 or 9 pixels then it generates fonts with width of 8 pixels. OPTIONS --fb Generate font for framebuffer. There are two important differ- ences between the framebuffer and the text mode. First, all fonts in text mode have to have matrix 8 pixels width. They also have to have either 256 or 512 glyphs. Second, in most text modes the hardware does some magic in order to use 8 pixels width fonts as if they were 9 pixels width. In order to achieve this the video hardware copies the 8th column in the 9th column of the glyphs with codes from 0xC0 to 0xDF and from 0x1C0 to 0x1DF. Bdf2psf is very careful when deciding where to place a particular glyph and as a result the encoding of the generated font is more or less arbitrary. --log logfile Record in the file logfile any problems during the conversion. bdf{+bdf} The "+"-separated list of the source BDF font(s). When a partic- ular symbol is defined in more than one of the specified fonts then fonts listed first take precedence. equivalence{+equivalence} A "+"-separated list of files defining an equivalence relation between the glyphs. See the section EQUIVALENCE FILES below. symbols{+[:]symbols} A "+"-separated list of files describing character sets. The generated font will support all specified character sets. When there is no space in the PSF font for all symbols, the character sets listed first take precedence. When a colon before a char- acter set is specified no warnings will be issued for symbols that could not be placed in the font. See the section CHARACTER SETS below. size The size of the PSF font. Usually 256 or 512 glyphs. psf The name of the generated font. If a file with this name already exists it will be overwritten. sfm Save in the file sfm the SFM of the generated font. This parame- ter is optional. CHARACTER SETS The encodings of the traditional console fonts a similar to the stan- dard encodings of the different languages. For example there are fonts for all variants of ISO 8859. This is redundant, for example ISO 8859-1, ISO 8859-9 and ISO 8859-15 differ only by few characters and can be easily covered by only one font. In order to determine the minimal set of character sets a clustering algorithm has been used. The source code of fontconfig contains lists of the characters that most languages require - one list per language. We started with one character set per language and used the clustering algorithm in order to join the character sets to bigger. The character sets described in files installed in the directory fontsets were the result of the algorithm. These files list the unicodes of the symbols of the character set, one per line. Comments starting with a sharp sign are also allowed. The files ascii.set, linux.set, freebsd.set and useful.set contain four special character sets. The first lists the ASCII symbols and the sec- ond and the third list the symbols from the so called alternate charac- ter set (see section "Line Graphics" of terminfo(5)) - one for Linux and one for FreeBSD. Notice that in order to limit itself to the cp437 character set, the Linux console driver does some approximations of the symbols from the alternate character set. For example it prints U+256A (BOX DRAWINGS VERTICAL SINGLE AND HORIZONTAL DOUBLE) instead of the not-equal sign. The file linux.set lists the symbols used by the Linux console driver (i.e. U+256A instead of the not-equal sign). The sym- bols from freebsd.set are not fixed by the FreeBSD kernel, but there too there are some approximations. In most cases there is more available space in the fonts than neces- sary. The spare codes can be filled with the symbols from the use- ful.set special character set. It is convenient to use a colon before the name of useful.set on the command line of bdf2psf so no warnings are issued when there is no space in the font for some of these sym- bols. EQUIVALENCE FILES The equivalence files define an equivalence relation between unicodes. The sharp sign is used for comments, the empty lines are ignored. All other lines should list two or more unicodes. Only one glyph will be allocated in the PSF font for these unicodes. Example: U+2126 U+03A9 # U+2126: OHM SIGN # U+03A9: GREEK CAPITAL LETTER OMEGA U+041D U+0048 # U+041D: CYRILLIC CAPITAL LETTER EN # U+0048: LATIN CAPITAL LETTER H This equivalence file says that U+2126 (the Ohm sign) and U+03A9 (Omega) have the same look so only one glyph is enough for them. And also U+041D (Cyrillic En) and U+0048 (Latin H) look the same. Two equivalence files are provided - standard.equivalents and ara- bic.equivalents. The first one can be used for all fonts. The purpose of the second is to reduce the number of the necessary glyphs for the Arabic letters at the cost of the font quality. It should be used only for fonts that have to support Arabic but there is not enough space in the PSF font for all Arabic characters. The Uni1 character set is a character set that requires arabic.equivalents. FILES All mentioned files and directories are usually installed in /usr/share/bdf2psf or /usr/local/share/bdf2psf. AUTHOR Anton Zinoviev console-setup 2006-01-16 BDF2PSF(1)