===============================================================================
		Software Package - Component
===============================================================================
	1. ReleaseNotes.doc

	2. document/

	3. driver source code

		3.1 Makefile - to build the modules

		3.2 Script and configuration for DHCP:
			"wlan0dhcp"
			"ifcfg-wlan0"

		3.3 Example of supplicant configuration file:
			"wpa1.conf"

		3.4 Script to run wpa_supplicant
			"runwpa"

		3.5 Script to clean relative modules
			"clean"

	4. wpa_supplicant/wpa_supplicant-0.6.9_wps_patch_20100201.zip
			The tool help the wlan network to communicate under the
			protection of WPAPSK mechanism (WPA/WPA2) and add WPS patch

	5. install.sh
	   Script to easy make 8192cu driver.
	
==================================================================================================================
		User Guide(1) - connecting wireless networking using "Network Manager" GUI utility (For PC Linux)
==================================================================================================================
			(1) Network Manager is a utility attempts to make use of wireless networking easy.

			(2) Notes: if you want to use the following command-line method to connect wireless networking,
						please disable the "Network Manager", because "Network Manager" will conflict with method of command line .

==================================================================================================================
		User Guide(2) - Using the wpa_cli & wpa_supplicant tools (For embedded Linux)
==================================================================================================================

	Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

==================================================================================================================
		User Guide(3) - Set wireless lan MIBs in Command Line (Legacy command - Not recommend)
==================================================================================================================
This driver uses Wireless Extension as an interface allowing you to set
Wireless LAN specific parameters.

Current driver supports "iwlist" to show the device status of nic
        iwlist wlan0 [parameters]
where
        parameter explaination      	[parameters]
        -----------------------     	-------------
        Show available chan and freq	freq / channel
        Show and Scan BSS and IBSS 	scan[ning]
        Show supported bit-rate         rate / bit[rate]

For example:
	iwlist wlan0 channel
	iwlist wlan0 scan
	iwlist wlan0 rate

Driver also supports "iwconfig", manipulate driver private ioctls, to set
MIBs.

	iwconfig wlan0 [parameters] [val]
where
	parameter explaination      [parameters]        [val] constraints
        -----------------------     -------------        ------------------
        Connect to AP by address    ap              	[mac_addr]
        Set the essid, join (I)BSS  essid             	[essid]
        Set operation mode          mode                {Managed|Ad-hoc}
        Set keys and security mode  key/enc[ryption]    {N|open|restricted|off}

For example:
	iwconfig wlan0 essid "ap_name"
	iwconfig wlan0 ap XX:XX:XX:XX:XX:XX
	iwconfig wlan0 mode Ad-hoc
	iwconfig wlan0 essid "name" mode Ad-hoc
	iwconfig wlan0 key 0123456789 [2] open
	iwconfig wlan0 key off
	iwconfig wlan0 key restricted [3] 0123456789
        Note: Better to set these MIBS without GUI such as NetworkManager and be sure that our
              nic has been brought up before these settings. WEP key index 2-4 is not supportted by
              NetworkManager.

===============================================================================
		Getting IP address (For User Guide(2) & User Guide(3))
===============================================================================
After start up the nic and connect to AP successfully, the network needs to obtain an IP address 
before transmit/receive data.
This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"
command, or using DHCP.

If using DHCP, setting steps is as below:
	(1)check if the WiFi had connected to an AP via "iwconfig" command
		$> iwconfig

	(2)run the script which run the dhclient
		$> ./wlan0dhcp
           or
		dhcpcd wlan0
              	(Some network admins require that you use the
              	hostname and domainname provided by the DHCP server.
              	In that case, use
		dhcpcd -HD wlan0)


===============================================================================
		WPAPSK/WPA2PSK - using wpa_supplicant (For User Guide(3))
===============================================================================

	Wpa_supplicant helps to secure wireless connection with the protection of
WPAPSK/WPA2PSK mechanism. Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
		WPS - PIN & PBC methods
===============================================================================

		(*) Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
		Power Saving Mode
===============================================================================

		(*) Please refer to the document/HowTo enable the power saving functionality.doc